Canon imagePROGRAF iPF830 Operation Guide - Page 129

Rel lever is in wrong position., Rewinding error., Media take-up unit ready.

Get Canon imagePROGRAF iPF830 PDF manuals and user guides View all Canon imagePROGRAF iPF830 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 129 highlights

iPF830 Series Rel lever is in wrong position. Cause Paper can be retracted only up to 17 mm (0.7 in) when using the Media Take-up Unit. Corrective Action Canceling manual advancing. Rel lever is in wrong position. Cause The Release Lever is up. Corrective Action Lower the Release Lever. If the error occurs again, turn off the printer and wait a while before restoring power. Rewinding error. Cause There is some foreign object near the Media Take-up Unit sensor and the roll cannot be detected. Corrective Action Remove the foreign object near the sensor. The roll is out of range of detection by the Media Take-up Unit sensor. Reload the roll. Press the OK button to clear the error. (See "Loading Rolls in the Printer.") ➔P.15 (See "Using the Media Take-up Unit.") ➔User's Guide A paper jam has occurred and the roll cannot be rewound. Remove the paper from the Media Take-up Unit. Press the OK button to clear the error. The Media Take-up Unit sensor is damaged. Contact your Canon dealer for assistance. *1:Printing will stop momentarily if an error involving the Media Take-up Unit occurs. If you prefer printing not to stop, set Skip Take-Up Err to On. However, note that this error may cause paper jams and affect the printing quality. Media take-up unit ready. Cause The Take-up Reel setting in the printer Set./Adj. Menu was changed from Enable to Disable, but a print job was received before the roll was removed. Corrective Action Press ▲ or ▼ to select Stop Printing, and then press the OK button to stop printing. The mode switches from take-up mode to regular mode after you change the Take-up Reel setting in the Set./Adj. Menu from Enable to Disable and lift the Release Lever to remove a roll, or after you execute Paper Cutting. Press ▲ or ▼ to select Print, and then press the OK button to resume printing. Error Message Messages regarding paper Turn on the media take-up unit. Cause The Take-up Reel setting in the control panel menu was changed to Enable while the power to the Take-up Reel was off and the Roll Media lamp on the control panel was lit. Corrective Action Turn the Media Take-up Unit on. The Take-up Reel setting in the control panel menu changes to Disable. Borderless printng not possible. Cause Corrective Action The print job received specifies Follow these steps to change the settings of the print job to enable borderless printing. a type or width of paper that is not compatible with borderless 1. Press ▲ or ▼ to select Stop Printing, and then press the OK button. printing. 2. Make sure the correct printer driver for the printer is selected and try printing again. For information on types of paper compatible with borderless printing, refer to the Paper Ref- erence Guide. (See "Displaying the Paper Reference Guide.") ➔User's Guide 129 Basic Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Cause
Corrective Action
Paper can be retracted only up to 17 mm (0.7 in) when using the Media
Take-up Unit.
Canceling manual advancing.
Rel lever is in wrong position.
Rel lever is in wrong position.
Cause
Corrective Action
The Release Lever is up.
Lower the Release Lever.
If the error occurs again, turn off the printer and wait a while before restoring power.
Rewinding error.
Rewinding error.
Cause
Corrective Action
There is some foreign object near the Media Take-up Unit sensor and the
roll cannot be detected.
Remove the foreign object near the sensor.
The roll is out of range of detection by the Media Take-up Unit sensor.
Reload the roll.
Press the
OK
button to clear the error.
(See "Loading Rolls in the Printer.")
➔
P.15
(See "Using the Media Take-up Unit.")
➔
User's Guide
A paper jam has occurred and the roll cannot be rewound.
Remove the paper from the Media Take-up Unit.
Press the
OK
button to clear the error.
The Media Take-up Unit sensor is damaged.
Contact your Canon dealer for assistance.
*1:
Printing will stop momentarily if an error involving the Media Take-up Unit occurs. If you prefer printing not to stop, set
Skip
Take-Up Err
to
On
. However, note that this error may cause paper jams and affect the printing quality.
Media take-up unit ready.
Media take-up unit ready.
Cause
Corrective Action
The
Take-up Reel
setting in the printer
Set./Adj. Menu
was changed from
Enable
to
Disable
, but a print job
was received before the roll was removed.
Press
▲
or
▼
to select
Stop Printing
, and then press the
OK
button to
stop printing.
The mode switches from take-up mode to regular mode after you change
the
Take-up Reel
setting in the
Set./Adj. Menu
from
Enable
to
Disable
and lift the Release Lever to remove a roll, or after you execute
Paper
Cutting
.
Press
▲
or
▼
to select
Print
, and then press the
OK
button to resume
printing.
Turn on the media take-up unit.
Turn on the media take-up unit.
Cause
Corrective Action
The
Take-up Reel
setting in the control panel menu was changed to
Enable
while the power
to the
Take-up Reel
was off and the
Roll Media lamp
on the control panel was lit.
Turn the Media Take-up Unit on.
The
Take-up Reel
setting in the
control panel menu changes to
Disable
.
Borderless printng not possible.
Borderless printng not possible.
Cause
Corrective Action
The print job received specifies
a type or width of paper that is
not compatible with borderless
printing.
Follow these steps to change the settings of the print job to enable borderless printing.
1.
Press
▲
or
▼
to select
Stop Printing
, and then press the
OK
button.
2.
Make sure the correct printer driver for the printer is selected and try printing again.
For information on types of paper compatible with borderless printing, refer to the
Paper Ref-
erence Guide
.
(See "Displaying the Paper Reference Guide.")
➔
User's Guide
iPF830 Series
Rel lever is in wrong position.
Basic Guide
Error Message
Messages regarding paper
129