Compaq 222863-001 TaskSmart W2200 Maintenance and Service Guide - Page 23

Observe the following guidelines when installing additional memory

Get Compaq 222863-001 - TaskSmart W2200 Model 10 PDF manuals and user guides View all Compaq 222863-001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

2-8 Compaq TaskSmart W2200 Appliance Server Maintenance and Service Guide To remove a DIMM from the system board: 1. Power down the server. See "Powering Down the Server" earlier in this chapter. CAUTION: Electrostatic discharge (ESD) can damage electronic components. Ensure that you are properly grounded (earthed) before beginning any installation procedure. Refer to "Electrostatic Discharge Information" earlier in this chapter. 2. Remove the access panel. See "Access Panel" earlier in this chapter. 3. Open the DIMM socket latches on the socket to be serviced . The module pops out of the socket when the latches are released. CAUTION: Remove DIMMs carefully to avoid bumping the controller module on the system board. The module connector pins can be damaged if the module is suddenly moved. 4. Pull the module out at the same angle as the DIMM socket on the system board . 1 1 2 Figure 2-3. Removing a DIMM from a DIMM socket Observe the following guidelines when installing additional memory: Memory installed in the TaskSmart W2200 appliance server must be PC133-MHz ECC registered SDRAM, 3.3 V, and 72 bits wide. To facilitate successive DIMM installations, install the DIMMs in sequential order, starting with DIMM socket 1. Refer to the illustration provided earlier in this section. CAUTION: Use only Compaq DIMMs. DIMMs from other sources can adversely affect data integrity.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
2-8
Compaq TaskSmart W2200 Appliance Server Maintenance and Service Guide
To remove a DIMM from the system board:
1.
Power down the server. See “Powering Down the Server” earlier in this chapter.
CAUTION:
Electrostatic discharge (ESD) can damage electronic components. Ensure that you
are properly grounded (earthed) before beginning any installation procedure. Refer to
“
Electrostatic Discharge Information
”
earlier in this chapter.
2.
Remove the access panel. See “Access Panel” earlier in this chapter.
3.
Open the DIMM socket latches on the socket to be serviced
. The module pops out of
the socket when the latches are released.
CAUTION:
Remove DIMMs carefully to avoid bumping the controller module on the system
board. The module connector pins can be damaged if the module is suddenly moved.
4.
Pull the module out at the same angle as the DIMM socket on the system board
.
1
1
2
Figure 2-3.
Removing a DIMM from a DIMM socket
Observe the following guidelines when installing additional memory:
■
Memory installed in the TaskSmart W2200 appliance server must be PC133-MHz ECC
registered SDRAM, 3.3 V, and 72 bits wide.
■
To facilitate successive DIMM installations, install the DIMMs in sequential order,
starting with DIMM socket 1. Refer to the illustration provided earlier in this section.
CAUTION:
Use only Compaq DIMMs. DIMMs from other sources can adversely affect data
integrity.