Compaq 222863-001 TaskSmart W2200 Maintenance and Service Guide - Page 44

TwoDevice Terminated SCSI Cable (Models 20 and 30), Disconnect the SCSI cable from the hard drives

Get Compaq 222863-001 - TaskSmart W2200 Model 10 PDF manuals and user guides View all Compaq 222863-001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Removal and Replacement Procedures 2-29 Two-Device Terminated SCSI Cable (Models 20 and 30) To remove the two-device terminated SCSI cable: 1. Power down the server. See "Powering Down the Server" earlier in this chapter. 2. Remove the access panel. See "Access Panel" earlier in this chapter. 3. Remove the PCI riser board assembly. See "PCI Riser Board Assembly" earlier in this chapter. 4. Remove the center wall. See "Center Wall" earlier in this chapter. CAUTION: To avoid hardware damage to the board, cable, or system board, use caution when replacing the SCSI module onto the support posts. 5. Disconnect the SCSI cable from the hard drives 6. Disconnect the SCSI cable from the SCSI controller module . 1 1 2 Figure 2-24. Removing the two-device terminated SCSI cable To replace the two-device terminated SCSI cable, reverse steps 2 through 6.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Removal and Replacement Procedures
2-29
Two-Device Terminated SCSI Cable (Models 20 and 30)
To remove the two-device terminated SCSI cable:
1.
Power down the server. See “Powering Down the Server” earlier in this chapter.
2.
Remove the access panel. See “Access Panel” earlier in this chapter.
3.
Remove the PCI riser board assembly. See “PCI Riser Board Assembly” earlier in this
chapter.
4.
Remove the center wall. See “Center Wall” earlier in this chapter.
CAUTION:
To avoid hardware damage to the board, cable, or system board, use caution when
replacing the SCSI module onto the support posts.
5.
Disconnect the SCSI cable from the hard drives
6.
Disconnect the SCSI cable from the SCSI controller module
.
1
1
2
Figure 2-24.
Removing the two-device terminated SCSI cable
To replace the two-device terminated SCSI cable, reverse steps 2 through 6.