Compaq 222863-001 TaskSmart W2200 Maintenance and Service Guide - Page 34

Ultra ATA/100 Controller Module (Model€10 - pressurements

Get Compaq 222863-001 - TaskSmart W2200 Model 10 PDF manuals and user guides View all Compaq 222863-001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Removal and Replacement Procedures 2-19 Ultra ATA/100 Controller Module (Model 10) To remove the ATA controller module: 1. Power down the server. See "Powering Down the Server" earlier in this chapter. 2. Remove the access panel. See "Access Panel" earlier in this chapter. CAUTION: Prevent damage to the connector pins by lifting the ATA controller module evenly and with equal pressure on the board. Tilting the board causes the connector pins to bend. 3. Remove the ATA controller module by pinching the tops of the support posts , and then carefully lifting the ATA controller module from the system board . 4. Disconnect the ATA cable from the ATA controller connector on the module . See "ATA Cable (Model 10)" later in this chapter. 2 3 3 1 Figure 2-14. Removing the ATA controller module from the system board (center wall removed for clarity) To replace the ATA controller module, reverse steps 2 through 4, ensuring that the ATA controller module securely seats on the support posts.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Removal and Replacement Procedures
2-19
Ultra ATA/100 Controller Module (Model 10)
To remove the ATA controller module:
1.
Power down the server. See “Powering Down the Server” earlier in this chapter.
2.
Remove the access panel. See “Access Panel” earlier in this chapter.
CAUTION:
Prevent damage to the connector pins by lifting the ATA controller module evenly
and with equal pressure on the board. Tilting the board causes the connector pins to bend.
3.
Remove the ATA controller module by pinching the tops of the support posts
, and then
carefully lifting the ATA controller module from the system board
.
4.
Disconnect the ATA cable
from the ATA controller connector on the
module
. See
“ATA Cable (Model 10)” later in this chapter.
1
3
2
3
Figure 2-14.
Removing the ATA controller module from the system board (center wall removed for
clarity)
To replace the ATA controller module, reverse steps 2 through 4, ensuring that the ATA
controller module securely seats on the support posts.