Compaq 222863-001 TaskSmart W2200 Maintenance and Service Guide - Page 32

Hard Drives, See Two-Device

Get Compaq 222863-001 - TaskSmart W2200 Model 10 PDF manuals and user guides View all Compaq 222863-001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Removal and Replacement Procedures 2-17 Hard Drives To remove a hard drive from the hard drive bay: 1. Power down the server. See "Powering Down the Server" earlier in this chapter. 2. Remove the access panel. See "Access Panel" earlier in this chapter. 3. Disconnect the SCSI or ATA cables from the hard drive(s) . See "Two-Device Terminated SCSI Cable (Models 20 and 30)" or "ATA Cable" later in this chapter. 4. Disconnect the hard drive power cable from the hard drive(s) . 5. Remove the hard drive and hard drive tray by performing the following steps: a. Loosen the thumbscrew that secures the hard drive tray to the chassis . b. Slide the tray toward the rear of the server, and then lift the tray out of the chassis . 4 2 3 1 Figure 2-12. Removing a hard drive tray from the chassis (center wall removed for clarity)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Removal and Replacement Procedures
2-17
Hard Drives
To remove a hard drive from the hard drive bay:
1.
Power down the server. See “Powering Down the Server” earlier in this chapter.
2.
Remove the access panel. See “Access Panel” earlier in this chapter.
3.
Disconnect the SCSI or ATA cables from the hard drive(s)
. See “Two-Device
Terminated SCSI Cable (Models 20 and 30)” or “ATA Cable” later in this chapter.
4.
Disconnect the hard drive power cable from the hard drive(s)
.
5.
Remove the hard drive and hard drive tray by performing the following steps:
a.
Loosen the thumbscrew that secures the hard drive tray to the chassis
.
b.
Slide the tray toward the rear of the server, and then lift
the tray out of the chassis
.
1
2
3
4
Figure 2-12.
Removing a hard drive tray from the chassis (center wall removed for clarity)