Compaq 222863-001 TaskSmart W2200 Maintenance and Service Guide - Page 36

CDROM/Diskette Drive Assembly Backplane

Get Compaq 222863-001 - TaskSmart W2200 Model 10 PDF manuals and user guides View all Compaq 222863-001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Removal and Replacement Procedures 2-21 CD-ROM/Diskette Drive Assembly Backplane To remove the CD-ROM/diskette drive assembly backplane: 1. Power down the server. See "Powering Down the Server" earlier in this chapter. 2. Remove the access panel. See "Access Panel" earlier in this chapter. 3. Remove the shipping/ejector key. See "Shipping/Ejector Key" earlier in this chapter. 4. Remove the CD-ROM/diskette drive assembly. See "CD-ROM/Diskette Drive Assembly" earlier in this chapter. 5. Disconnect the CD-ROM/diskette drive assembly cable from the CD-ROM/diskette drive assembly backplane . See "CD-ROM/Diskette Drive Assembly Cable" later in this chapter. 6. Carefully pull back and hold the plastic retaining clip . 7. Lift the backplane vertically until it unseats from the drive bracket and user interface board . 2 3 1 Figure 2-16. Removing a CD-ROM/diskette drive assembly backplane (center wall removed for clarity) To replace the CD-ROM/diskette drive assembly backplane, reverse steps 2 through 7.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Removal and Replacement Procedures
2-21
CD-ROM/Diskette Drive Assembly Backplane
To remove the CD-ROM/diskette drive assembly backplane:
1.
Power down the server. See “Powering Down the Server” earlier in this chapter.
2.
Remove the access panel. See “Access Panel” earlier in this chapter.
3.
Remove the shipping/ejector key. See “Shipping/Ejector Key” earlier in this chapter.
4.
Remove the CD-ROM/diskette drive assembly. See “CD-ROM/Diskette Drive Assembly”
earlier in this chapter.
5.
Disconnect the CD-ROM/diskette drive assembly cable from the CD-ROM/diskette drive
assembly backplane
. See “CD-ROM/Diskette Drive Assembly Cable” later in this
chapter.
6.
Carefully pull back and hold the plastic retaining clip
.
7.
Lift the backplane vertically until it unseats from the drive bracket and user interface
board
.
1
3
2
Figure 2-16.
Removing a CD-ROM/diskette drive assembly backplane (center wall removed for
clarity)
To replace the CD-ROM/diskette drive assembly backplane, reverse steps 2 through 7.