Compaq 222863-001 TaskSmart W2200 Maintenance and Service Guide - Page 43

Cables, ATA Cable (Model 10)

Get Compaq 222863-001 - TaskSmart W2200 Model 10 PDF manuals and user guides View all Compaq 222863-001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

2-28 Compaq TaskSmart W2200 Appliance Server Maintenance and Service Guide Cables The following subsections contain removal and replacement procedures for the standard cables that ship with the TaskSmart W2200 appliance server: ATA Cable (Model 10) Two-Device Terminated SCSI Cable (Models 20 and 30) CD-ROM/Diskette Drive Assembly Cable Remote Insight Lights-Out Edition Board Remote Management Cable (Model 30) ATA Cable (Model 10) To remove the ATA cable: 1. Power down the server. See "Powering Down the Server" earlier in this chapter. 2. Remove the access panel. See "Access Panel" earlier in this chapter. 3. Remove the PCI riser board assembly. See "PCI Riser Board Assembly" earlier in this chapter. 4. Remove the center wall. See "Center Wall" earlier in this chapter. 5. Disconnect the ATA cable from the ATA controller connectors on the ATA controller module . 6. Disconnect the ATA cable from the hard drive . 2 1 1 Figure 2-23. Removing the ATA cable Reverse steps 2 through 6 to replace the ATA cable.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
2-28
Compaq TaskSmart W2200 Appliance Server Maintenance and Service Guide
Cables
The following subsections contain removal and replacement procedures for the standard cables
that ship with the TaskSmart W2200 appliance server:
■
ATA Cable (Model 10)
■
Two-Device Terminated SCSI Cable (Models 20 and 30)
■
CD-ROM/Diskette Drive Assembly Cable
■
Remote Insight Lights-Out Edition Board Remote Management Cable (Model 30)
ATA Cable (Model 10)
To remove the ATA cable:
1.
Power down the server. See “Powering Down the Server” earlier in this chapter.
2.
Remove the access panel. See “Access Panel” earlier in this chapter.
3.
Remove the PCI riser board assembly. See “PCI Riser Board Assembly” earlier in this
chapter.
4.
Remove the center wall. See “Center Wall” earlier in this chapter.
5.
Disconnect the ATA cable from the ATA controller connectors
on the ATA controller
module
.
6.
Disconnect the ATA cable from the hard drive
.
1
2
1
Figure 2-23.
Removing the ATA cable
Reverse steps 2 through 6 to replace the ATA cable.