Compaq ProSignia 500 Compaq ProSignia Family of PC Servers Maintenance and Ser - Page 25

Not Been Detected By, Secondary Disk Port

Get Compaq ProSignia 500 PDF manuals and user guides View all Compaq ProSignia 500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

612-Secondary Floppy Configuration error. Run the EISA Port Address Assignment Configuration Utility Conflict and correct. 702-A coprocessor has Installed coprocessor Run the EISA been detected that was not configured. Configuration Utility not reported by CMOS. and correct. 703-CMOS Reports A Coprocessor or 1. Run the EISA Coprocessor That Has configuration error. Configuration Not Been Detected By Utility and correct. POST 2. Replace the coprocessor. 1151-COM Port 1 Both external and Run the EISA internal serial ports Configuration Utility are assigned to COM1. and correct. 1152-COM Port 2 Both external and Run the EISA internal serial ports Configuration Utility are assigned to COM2. and correct. Error Code Probable Source Action of Problem 1153-COM Port 3 Both external and Run the EISA internal serial ports Configuration Utility are assigned to COM3. and correct. 1154-COM Port 4 Both external and Run the EISA internal serial ports Configuration Utility are assigned to COM4. and correct. 1701-SCSI Controller A test on the Run Diagnostics. Failure Controller failed. Replace failed assembly as indicated or, contact your service provider. 1771-Primary Disk Port Internal and external Run the EISA Address Assignment hard drive controllers Configuration Utility Conflict are both assigned to and correct. the primary address. 1772-Secondary Disk Port Address Assignment Run the EISA Conflict. Internal Configuration Utility and external hard and correct. drive controllers are both assigned to the secondary address. 1777-Slot # Drive Array Configuration error. Run the EISA Controller has been Configuration Utility upgraded. Run System and correct. Configuration Utility 1778-Slot # Drive Array This message appears No action necessary. resuming Automatic Data whenever a controller Recovery process reset or power cycle occurs while Automatic

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
---------------------------------------------------------------------------
612-Secondary Floppy
Configuration error.
Run the EISA
Port Address Assignment
Configuration Utility
Conflict
and correct.
---------------------------------------------------------------------------
702-A coprocessor has
Installed coprocessor
Run the EISA
been detected that was
not configured.
Configuration Utility
not reported by CMOS.
and correct.
---------------------------------------------------------------------------
703-CMOS Reports A
Coprocessor or
1. Run the EISA
Coprocessor That Has
configuration error.
Configuration
Not Been Detected By
Utility and correct.
POST
2. Replace the
coprocessor.
---------------------------------------------------------------------------
1151-COM Port 1
Both external and
Run the EISA
internal serial ports
Configuration Utility
are assigned to COM1.
and correct.
---------------------------------------------------------------------------
1152-COM Port 2
Both external and
Run the EISA
internal serial ports
Configuration Utility
are assigned to COM2.
and correct.
---------------------------------------------------------------------------
Error Code
Probable Source
Action
of Problem
---------------------------------------------------------------------------
1153-COM Port 3
Both external and
Run the EISA
internal serial ports
Configuration Utility
are assigned to COM3.
and correct.
---------------------------------------------------------------------------
1154-COM Port 4
Both external and
Run the EISA
internal serial ports
Configuration Utility
are assigned to COM4.
and correct.
---------------------------------------------------------------------------
1701-SCSI Controller
A test on the
Run Diagnostics.
Failure
Controller failed.
Replace failed assembly
as indicated or, contact
your service provider.
---------------------------------------------------------------------------
1771-Primary Disk Port
Internal and external
Run the EISA
Address Assignment
hard drive controllers Configuration Utility
Conflict
are both assigned to
and correct.
the primary address.
---------------------------------------------------------------------------
1772-Secondary Disk Port
Address Assignment
Run the EISA
Conflict. Internal
Configuration Utility
and external hard
and correct.
drive controllers are
both assigned to the
secondary address.
---------------------------------------------------------------------------
1777-Slot # Drive Array
Configuration error.
Run the EISA
Controller has been
Configuration Utility
upgraded. Run System
and correct.
Configuration Utility
---------------------------------------------------------------------------
1778-Slot # Drive Array
This message appears
No action necessary.
resuming Automatic Data
whenever a controller
Recovery process
reset or power cycle
occurs while Automatic