Compaq ProSignia 500 Compaq ProSignia Family of PC Servers Maintenance and Ser - Page 50

Logical Drive X status = WRONG DRIVE REPLACED, No configuration for Accelerator Board

Get Compaq ProSignia 500 PDF manuals and user guides View all Compaq ProSignia 500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Logical Drive X status = RECOVERING A physical drive in this logical drive has failed and has now been replaced. The replaced drive is rebuilding from the mirror drive or the parity data. Nothing needs to be done. Normal operations can occur. Logical Drive X status = WRONG DRIVE REPLACED A physical drive in this logical drive has failed. The incorrect drive was replaced. Replace the drive that was incorrectly replaced. Then, replace the original drive that failed with a new drive. Do not run the EISA Configuration Utility to reconfigure - you will lose data on the drive. Mirror data miscompare Data was found at reinitialization in the posted write memory, however, the mirror data compare test failed resulting in data being marked as invalid. Data loss is possible. Replace the array accelerator board. Mirrored memory location errors Soft errors occurred when attempting to read the same data from both sides of the mirrored memory errors. Data loss will occur. Replace the array accelerator board. No configuration for Accelerator Board The array accelerator board has not been configured. If the array accelerator board is present, run the EISA Configuration Utility to configure the board. Physical Drive (bay) X error occurred This message displays detailed information on any drive errors that were returned to DAAD while issuing drive commands. Check for other error conditions. Physical drive (bay) X has loose cable The array controller could not communicate with this drive at power-up. This drive has not previously failed. Check all cable connections first. The cables could be bad, loose, or disconnected. Turn on the system and attempt to reconnect data/power cable

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
---------------------------------------------------------------------------
Logical Drive X status = RECOVERING
A physical drive in this logical drive has failed and has now been
replaced. The replaced drive is rebuilding from the mirror drive or the
parity data.
Nothing needs to be done. Normal operations can occur.
---------------------------------------------------------------------------
Logical Drive X status = WRONG DRIVE REPLACED
A physical drive in this logical drive has failed. The incorrect drive was
replaced.
Replace the drive that was incorrectly replaced. Then, replace the
original drive that failed with a new drive. Do not run the EISA
Configuration Utility to reconfigure - you will lose data on the drive.
---------------------------------------------------------------------------
Mirror data miscompare
Data was found at reinitialization in the posted write memory, however, the
mirror data compare test failed resulting in data being marked as invalid.
Data loss is possible.
Replace the array accelerator board.
---------------------------------------------------------------------------
Mirrored memory location errors
Soft errors occurred when attempting to read the same data from both sides
of the mirrored memory errors. Data loss will occur.
Replace the array accelerator board.
---------------------------------------------------------------------------
No configuration for Accelerator Board
The array accelerator board has not been configured.
If the array accelerator board is present, run the EISA Configuration
Utility to configure the board.
---------------------------------------------------------------------------
Physical Drive (bay) X error occurred
This message displays detailed information on any drive errors that were
returned to DAAD while issuing drive commands.
Check for other error conditions.
---------------------------------------------------------------------------
Physical drive (bay) X has loose cable
The array controller could not communicate with this drive at power-up.
This drive has not previously failed.
Check all cable connections first. The cables could be bad, loose, or
disconnected. Turn on the system and attempt to reconnect data/power cable