Compaq ProSignia 500 Compaq ProSignia Family of PC Servers Maintenance and Ser - Page 47

Drive X indicates position Y, This drive may need to be replaced. Check for other errors.

Get Compaq ProSignia 500 PDF manuals and user guides View all Compaq ProSignia 500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

acknowledged. The drive or cable may be bad. Check the other error messages on the Diagnosis screen to determine resolution. Drive (bay) X firmware needs upgrading The firmware on this physical drive is below the latest recommended version. Call your Authorized COMPAQ Reseller to obtain the latest upgraded firmware. Drive (bay) X has invalid M&P stamp The physical drive has invalid monitor and performance data present. Run the latest COMPAQ Diagnostics Utility to properly initialize this drive. Drive X indicates position Y This message indicates which physical drive appears to be scrambled or in the wrong drive in a bay that it was originally configured for. Examine the graphical drive representation on DAAD to determine proper drive locations. Remove drive X and place it in drive position Y. Rearrange the drives according to the DAAD instructions. Drive (bay) X RIS copy mismatch The copies of the RIS on this drive do not match. This drive may need to be replaced. Check for other errors. Drive (bay) X upload code not readable An error occurred while DAAD was trying to read the upload code information from this drive. If there were multiple errors, this drive may need to be replaced. Duplicate write memory error Data could not be written to the array accelerator board in duplicate due to the detection of parity errors. This is not a data loss situation. Replace the array accelerator board. Error occurred reading RIS copy from drive (bay) X An error occurred while DAAD was trying to read the RIS from this drive.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
acknowledged.
The drive or cable may be bad. Check the other error messages on the
Diagnosis screen to determine resolution.
---------------------------------------------------------------------------
Drive (bay) X firmware needs upgrading
The firmware on this physical drive is below the latest recommended
version.
Call your Authorized COMPAQ Reseller to obtain the latest upgraded
firmware.
---------------------------------------------------------------------------
Drive (bay) X has invalid M&P stamp
The physical drive has invalid monitor and performance data present.
Run the latest COMPAQ Diagnostics Utility to properly initialize this
drive.
---------------------------------------------------------------------------
Drive X indicates position Y
This message indicates which physical drive appears to be scrambled or in
the wrong drive in a bay that it was originally configured for.
Examine the graphical drive representation on DAAD to determine proper
drive locations. Remove drive X and place it in drive position Y. Rearrange
the drives according to the DAAD instructions.
---------------------------------------------------------------------------
Drive (bay) X RIS copy mismatch
The copies of the RIS on this drive do not match.
This drive may need to be replaced. Check for other errors.
---------------------------------------------------------------------------
Drive (bay) X upload code not readable
An error occurred while DAAD was trying to read the upload code information
from this drive.
If there were multiple errors, this drive may need to be replaced.
---------------------------------------------------------------------------
Duplicate write memory error
Data could not be written to the array accelerator board in duplicate due
to the detection of parity errors. This is not a data loss situation.
Replace the array accelerator board.
---------------------------------------------------------------------------
Error occurred reading RIS copy from drive (bay) X
An error occurred while DAAD was trying to read the RIS from this drive.