Compaq ProSignia 500 Compaq ProSignia Family of PC Servers Maintenance and Ser - Page 46

Controller reported POST error. Error Code: x, Drive bay X needs replacing DAAD Error 102

Get Compaq ProSignia 500 PDF manuals and user guides View all Compaq ProSignia 500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Replace the controller as soon as possible. Controller reported POST error. Error Code: x The controller returned an error from its internal Power-On Self Tests. Replace the controller. Controller restarted with a signature of zero DAAD did not find a valid configuration signature to use to get the data. Nonvolatile RAM may not be present (unconfigured) or the signature present in nonvolatile RAM may not match the signature on the controller. Run the EISA Configuration Utility to configure the controller and nonvolatile RAM. Disable command issued Posted writes have been disabled by the issuing of the Accelerator Disable command. This occurred because of an operating system device driver. Restart the system. Run the EISA Configuration Utility to reinitialize the array accelerator board. Drive (bay) X needs replacing (DAAD Error 102) The 210-megabyte hard drive installed in the computer has firmware of 2.30 or 2.31. Replace the drive. Drive Monitoring features are unattainable DAAD was unable to get the monitor and performance data due to a fatal command problem such as drive time-out, or was unable to get the data due to these features not being supported on the controller. Check for other errors (time-outs, etc.). If no other errors occur, upgrade the firmware to a version that supports monitor and performance, if desired. Drive Monitoring is NOT enabled for drive bay X The monitor and performance features have not been enabled. Run the COMPAQ Diagnostics Utility 8.05 or higher to initialize the monitor and performance features. Drive time-out occurred on physical drive bay X DAAD issued a command to a physical drive and the command was never

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Replace the controller as soon as possible.
---------------------------------------------------------------------------
Controller reported POST error. Error Code: x
The controller returned an error from its internal Power-On Self Tests.
Replace the controller.
---------------------------------------------------------------------------
Controller restarted with a signature of zero
DAAD did not find a valid configuration signature to use to get the data.
Nonvolatile RAM may not be present (unconfigured) or the signature present
in nonvolatile RAM may not match the signature on the controller.
Run the EISA Configuration Utility to configure the controller and
nonvolatile RAM.
---------------------------------------------------------------------------
Disable command issued
Posted writes have been disabled by the issuing of the Accelerator Disable
command. This occurred because of an operating system device driver.
Restart the system. Run the EISA Configuration Utility to reinitialize the
array accelerator board.
---------------------------------------------------------------------------
Drive (bay) X needs replacing (DAAD Error 102)
The 210-megabyte hard drive installed in the computer has firmware of 2.30
or 2.31.
Replace the drive.
---------------------------------------------------------------------------
Drive Monitoring features are unattainable
DAAD was unable to get the monitor and performance data due to a fatal
command problem such as drive time-out, or was unable to get the data due
to these features not being supported on the controller.
Check for other errors (time-outs, etc.). If no other errors occur, upgrade
the firmware to a version that supports monitor and performance, if
desired.
---------------------------------------------------------------------------
Drive Monitoring is NOT enabled for drive bay X
The monitor and performance features have not been enabled.
Run the COMPAQ Diagnostics Utility 8.05 or higher to initialize the monitor
and performance features.
---------------------------------------------------------------------------
Drive time-out occurred on physical drive bay X
DAAD issued a command to a physical drive and the command was never