Compaq ProSignia 500 Compaq ProSignia Family of PC Servers Maintenance and Ser - Page 51

Soft Firmware Upgrade required, recon data will be lost.

Get Compaq ProSignia 500 PDF manuals and user guides View all Compaq ProSignia 500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

to the drive. If this does not work, replace the cable. If that does not work, the drive may need to be replaced. Physical drive (bay) X is a replacement drive This drive has been replaced. This message displays if a drive is replaced in a fault tolerant logical volume. If the replacement was intentional, allow the drive to rebuild. Physical drive (bay) X is a replacement drive marked OK This drive has been replaced and marked OK by the firmware. This may occur if a drive has an intermittent failure (for example, if a drive has previously failed, then when DAAD is run, the drive starts working again). Replace the drive. Physical drive (bay) X has failed The indicated physical drive has failed. Replace this drive. Physical drive (bay) X is undergoing drive recovery This drive is being rebuilt from the corresponding mirror or parity data. Normal operations should occur. Physical drive (bay) X was inadvertently replaced The physical drive was incorrectly replaced after another drive failed. Replace the drive that was incorrectly replaced and replace the original drive that failed. Do not run the EISA Configuration Utility and try to reconfigure - data will be lost. Set configuration command issued The configuration of the IDA-2 has been updated. The array accelerator board remains disabled until it is reinitialized. Run the EISA Configuration Utility to reinitialize the array accelerator board. Soft Firmware Upgrade required DAAD has determined that your controller is running firmware that has been soft upgraded by the COMPAQ Upgrade Utility. However, the firmware running is not present on all drives. This could be caused by the addition of new drives in the system.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
to the drive. If this does not work, replace the cable. If that does not
work, the drive may need to be replaced.
---------------------------------------------------------------------------
Physical drive (bay) X is a replacement drive
This drive has been replaced. This message displays if a drive is replaced
in a fault tolerant logical volume.
If the replacement was intentional, allow the drive to rebuild.
---------------------------------------------------------------------------
Physical drive (bay) X is a replacement drive marked OK
This drive has been replaced and marked OK by the firmware. This may occur
if a drive has an intermittent failure (for example, if a drive has
previously failed, then when DAAD is run, the drive starts working again).
Replace the drive.
---------------------------------------------------------------------------
Physical drive (bay) X has failed
The indicated physical drive has failed.
Replace this drive.
---------------------------------------------------------------------------
Physical drive (bay) X is undergoing drive recovery
This drive is being rebuilt from the corresponding mirror or parity data.
Normal operations should occur.
---------------------------------------------------------------------------
Physical drive (bay) X was inadvertently replaced
The physical drive was incorrectly replaced after another drive failed.
Replace the drive that was incorrectly replaced and replace the original
drive that failed. Do not run the EISA Configuration Utility and try to
reconfigure - data will be lost.
---------------------------------------------------------------------------
Set configuration command issued
The configuration of the IDA-2 has been updated. The array accelerator
board remains disabled until it is reinitialized.
Run the EISA Configuration Utility to reinitialize the array accelerator
board.
---------------------------------------------------------------------------
Soft Firmware Upgrade required
DAAD has determined that your controller is running firmware that has been
soft upgraded by the COMPAQ Upgrade Utility. However, the firmware running
is not present on all drives. This could be caused by the addition of new
drives in the system.