Compaq ProSignia 500 Compaq ProSignia Family of PC Servers Maintenance and Ser - Page 44

DAAD was verifying this interface, a serious problem was detected.

Get Compaq ProSignia 500 PDF manuals and user guides View all Compaq ProSignia 500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Battery pack X below reference voltage The indicated battery pack is below the required voltage levels. Allow for sufficient time for the batteries to recharge (36 hours). If the batteries have not recharged after 36 hours, replace the battery pack. Battery X not fully charged The battery is not fully charged. If 75% of the batteries present are fully charged, the array accelerator is fully operational. If more than 75% of the batteries are not fully charged, allow 36 hours to recharge them. Board not attached The IDA-2 board has been configured for use with an array accelerator board, but one is currently not attached. Locate the original array accelerator board and attach it to the IDA-2 board. CMOS present, controller not detected EISA nonvolatile RAM has a configuration for an array controller but there is no board in this slot. Either a board has been removed from the system or a board has been placed in the wrong slot. Place the array controller in the proper slot or run the EISA Configuration Utility to reconfigure nonvolatile RAM to reflect the removal or new position. Compatibility port problem detected You have the compatibility port configured for this IDA controller. When DAAD was verifying this interface, a serious problem was detected. A hardware problem has occurred and you should replace the IDA controller. Configuration signature is zero DAAD detected that nonvolatile RAM contains a configuration signature that is zero. Old versions of the EISA Configuration Utility could cause this. Run the latest version of EISA Configuration Utility to configure the controller and nonvolatile RAM. Configuration signature mismatch The array accelerator board has been configured for a different IDA-2 board. The configuration signature on the array accelerator board does not match the one stored on the IDA-2 board.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Battery pack X below reference voltage
The indicated battery pack is below the required voltage levels.
Allow for sufficient time for the batteries to recharge (36 hours). If the
batteries have not recharged after 36 hours, replace the battery pack.
---------------------------------------------------------------------------
Battery X not fully charged
The battery is not fully charged.
If 75% of the batteries present are fully charged, the array accelerator is
fully operational. If more than 75% of the batteries are not fully charged,
allow 36 hours to recharge them.
---------------------------------------------------------------------------
Board not attached
The IDA-2 board has been configured for use with an array accelerator
board, but one is currently not attached.
Locate the original array accelerator board and attach it to the IDA-2
board.
---------------------------------------------------------------------------
CMOS present, controller not detected
EISA nonvolatile RAM has a configuration for an array controller but there
is no board in this slot. Either a board has been removed from the system
or a board has been placed in the wrong slot.
Place the array controller in the proper slot or run the EISA Configuration
Utility to reconfigure nonvolatile RAM to reflect the removal or new
position.
---------------------------------------------------------------------------
Compatibility port problem detected
You have the compatibility port configured for this IDA controller. When
DAAD was verifying this interface, a serious problem was detected.
A hardware problem has occurred and you should replace the IDA controller.
---------------------------------------------------------------------------
Configuration signature is zero
DAAD detected that nonvolatile RAM contains a configuration signature that
is zero. Old versions of the EISA Configuration Utility could cause this.
Run the latest version of EISA Configuration Utility to configure the
controller and nonvolatile RAM.
---------------------------------------------------------------------------
Configuration signature mismatch
The array accelerator board has been configured for a different IDA-2
board. The configuration signature on the array accelerator board does not
match the one stored on the IDA-2 board.