Compaq ProSignia 500 Compaq ProSignia Family of PC Servers Maintenance and Ser - Page 48

Configuration Utility., The adapter does not have sufficient resources to perform operations to

Get Compaq ProSignia 500 PDF manuals and user guides View all Compaq ProSignia 500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

If there were multiple errors, this drive may need to be replaced. FYI: Drive (bay) X is non-Compaq supplied The installed drive was not supplied by Compaq. If problems exist with this drive, replace it with a COMPAQ drive. Identify controller data did not match with CMOS The identify controller data from the array controller did not match with the information stored in nonvolatile RAM. This could occur if new, previously configured drives have been placed in a system that has also been previously configured. It could also occur if the firmware on the controller has been upgraded and the EISA Configuration Utility was not run. Check the identify controller data under the INSPECT utility. If the firmware version field is the only thing different between the controller and nonvolatile RAM data, this is not a problem. Otherwise run the EISA Configuration Utility. Identify logical drive data did not match with CMOS The identify unit data from the array controller did not match with the information stored in nonvolatile RAM. This could occur if new, previously configured drives have been placed in a system that has also been previously configured. Run the EISA Configuration Utility to configure the controller and nonvolatile RAM. Insufficient adapter resources The adapter does not have sufficient resources to perform operations to the array accelerator board. Drive rebuild may be occurring. Operate the system without the array accelerator board until the drive rebuild completes. Less than 75% batteries at sufficient voltage The operation of the array accelerator board has been disabled due to less than 75% of the battery packs being at the sufficient voltage level. Allow sufficient time for the batteries to recharge (36 hours). If the batteries have not recharged after 36 hours, replace the array accelerator board. Logical drive X failed due to cache error This logical drive failed due to a catastrophic cache error. Replace the array accelerator board and reconfigure using the EISA

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
If there were multiple errors, this drive may need to be replaced.
---------------------------------------------------------------------------
FYI: Drive (bay) X is non-Compaq supplied
The installed drive was not supplied by Compaq.
If problems exist with this drive, replace it with a COMPAQ drive.
---------------------------------------------------------------------------
Identify controller data did not match with CMOS
The identify controller data from the array controller did not match with
the information stored in nonvolatile RAM. This could occur if new,
previously configured drives have been placed in a system that has also
been previously configured. It could also occur if the firmware on the
controller has been upgraded and the EISA Configuration Utility was not
run.
Check the identify controller data under the INSPECT utility. If the
firmware version field is the only thing different between the controller
and nonvolatile RAM data, this is not a problem. Otherwise run the EISA
Configuration Utility.
---------------------------------------------------------------------------
Identify logical drive data did not match with CMOS
The identify unit data from the array controller did not match with the
information stored in nonvolatile RAM. This could occur if new, previously
configured drives have been placed in a system that has also been
previously configured.
Run the EISA Configuration Utility to configure the controller and
nonvolatile RAM.
---------------------------------------------------------------------------
Insufficient adapter resources
The adapter does not have sufficient resources to perform operations to the
array accelerator board. Drive rebuild may be occurring.
Operate the system without the array accelerator board until the drive
rebuild completes.
---------------------------------------------------------------------------
Less than 75% batteries at sufficient voltage
The operation of the array accelerator board has been disabled due to less
than 75% of the battery packs being at the sufficient voltage level.
Allow sufficient time for the batteries to recharge (36 hours). If the
batteries have not recharged after 36 hours, replace the array accelerator
board.
---------------------------------------------------------------------------
Logical drive X failed due to cache error
This logical drive failed due to a catastrophic cache error.
Replace the array accelerator board and reconfigure using the EISA