D-Link DCS-6511 Product Manual - Page 16

Pendant Mount (DCS-34-2 - manual

Get D-Link DCS-6511 PDF manuals and user guides View all D-Link DCS-6511 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Section 2 - Installation Pendant Mount (DCS-34-2) 1. Attach the mounting plate to the bracket cap using the three screws as shown in Figure 3.1. Bracket Cap 2. Locate a suitable position on the ceiling for a 34 mm (+2 / -0 mm) hole to be cut. A template is included to aid in marking the mounting hole. 3. Cut the hole in the ceiling according to the template. Mounting Plate 4. Drill 4 separate 6 mm holes corresponding to the holes in the mounting template and insert the plastic anchors into these holes. 5. Place the rubber seal between the pendant bracket and the ceiling to ensure a waterproof seal between the ceiling and the bracket. (Figure 3.2) 6. Attach the pendant bracket to the ceiling using the screws provided. 7. Attach the bracket cap to the bottom of the pendant bracket, rotating the cap counterclockwise to tighten it into place. 8. Insert the screw into the base of the pendant bracket at the top of the bracket cap to secure the bracket cap into place. Figure 3.1 Rubber Seal Pendant Bracket D-Link DCS-6511 User Manual Figure 3.2 Bracket Cap 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
16
D-Link DCS-6511 User Manual
Section 2 - Installation
Pendant Mount (DCS-34-2)
1.
Attach the mounting plate to the bracket cap using the three screws as shown in
Figure
3.1
.
2.
Locate a suitable position on the ceiling for a 34 mm (+2 /
–
0 mm) hole to be cut. A
template is included to aid in marking the mounting hole.
3.
Cut the hole in the ceiling according to the template.
4.
Drill 4 separate 6 mm holes corresponding to the holes in the mounting template and
insert the plastic anchors into these holes.
5.
Place the rubber seal between the pendant bracket and the ceiling to ensure a
waterproof seal between the ceiling and the bracket. (Figure 3.2)
6.
Attach the pendant bracket to the ceiling using the screws provided.
7.
Attach the bracket cap to the bottom of the pendant bracket, rotating the cap counter-
clockwise to tighten it into place.
8.
Insert the screw into the base of the pendant bracket at the top of the bracket cap to
secure the bracket cap into place.
Pendant
Bracket
Bracket
Cap
Rubber
Seal
Figure 3.1
Bracket
Cap
Mounting
Plate
Figure 3.2