Dell Alienware m15 R7 Service Manual - Page 59

USB board, Removing the USB board

Get Dell Alienware m15 R7 PDF manuals and user guides View all Dell Alienware m15 R7 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

About this task The following image(s) indicate the location of the ethernet and audio board and provides a visual representation of the installation procedure. Steps 1. Connect the ethernet and audio board to the system board. 2. Align the screw holes on the ethernet and audio board to the screw holes on the system-board assembly. 3. Replace the two screws (M2x4) that secure the ethernet and audio board to the system-board assembly. 4. Turn the system-board assembly over. Next steps 1. Follow the procedure from step 6 to step 25 in Installing the system board. 2. Install the battery. 3. Install the rear-I/O cover. 4. Install the wireless card. 5. Install the 2230 solid-state drive or 2280 solid-state drive in slot one, whichever applicable. 6. Install the 2230 solid-state drive or 2280 solid-state drive in slot two, whichever applicable. 7. Install the base cover. 8. Follow the procedure in After working inside your computer. USB board Removing the USB board Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the 2230 solid-state drive or 2280 solid-state drive in slot one, whichever applicable. 4. Remove the 2230 solid state drive or 2280 solid-state drive in slot two, whichever applicable. 5. Remove the wireless card. 6. Remove the rear-I/O cover. 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
About this task
The following image(s) indicate the location of the ethernet and audio board and provides a visual representation of the installation
procedure.
Steps
1.
Connect the ethernet and audio board to the system board.
2.
Align the screw holes on the ethernet and audio board to the screw holes on the system-board assembly.
3.
Replace the two screws (M2x4) that secure the ethernet and audio board to the system-board assembly.
4.
Turn the system-board assembly over.
Next steps
1.
Follow the procedure from step 6 to step 25 in
Installing the system board
.
2.
Install the
battery
.
3.
Install the
rear-I/O cover
.
4.
Install the
wireless card
.
5.
Install the
2230 solid-state drive
or
2280 solid-state drive
in slot one, whichever applicable.
6.
Install the
2230 solid-state drive
or
2280 solid-state drive
in slot two, whichever applicable.
7.
Install the
base cover
.
8.
Follow the procedure in
After working inside your computer
.
USB board
Removing the USB board
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
3.
Remove the
2230 solid-state drive
or
2280 solid-state drive
in slot one, whichever applicable.
4.
Remove the
2230 solid state drive
or
2280 solid-state drive
in slot two, whichever applicable.
5.
Remove the
wireless card
.
6.
Remove the
rear-I/O cover
.
59