Dell Dimension 4400 Dell Dimension 4400 Systems Owner's Manual - Page 96

supervisor or setup password in

Get Dell Dimension 4400 PDF manuals and user guides View all Dell Dimension 4400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

www.dell.com | support.dell.com CAUTION: Before you begin this procedure, follow the safety instructions listed in "When Working Inside Your Computer" on page 12. If you forget your supervisor or setup password, you cannot operate your computer or change settings in the system setup program until you clear the forgotten password(s). NOTICE: The following procedure resets all standard settings for your computer. Before proceeding, record all current settings so that you can restore them when you finish this procedure. 1 Turn off the computer and unplug it from the electrical outlet (see page 20). 2 Open the computer cover (see page 65). 3 Locate the configuration jumper on the system board (see page 68), and move the jumper plug so that pins 2 and 3 are jumpered (to "clear" the password when you turn on the computer). 4 Close the computer cover (see page 87), connect your computer to an electrical outlet, and turn on the computer. 5 Access the system setup program (see page 94) and assign a new supervisor or setup password in the Maintenance menu. 6 Exit and save the system setup program settings. 7 After the computer boots, turn it off, and unplug it from the electrical outlet. 8 Open the computer cover again. 9 Move the configuration jumper plug so that pins 1 and 2 are jumpered (the "normal" setting). 10 Close the computer cover, connect your computer to an electrical outlet, and turn on the computer. 96 Appendix

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
96
Appendix
www.dell.com | support.dell.com
CAUTION:
Before you begin this procedure, follow the safety
instructions listed in "When Working Inside Your Computer" on
page 12.
If you forget your supervisor or setup password, you cannot operate your
computer or change settings in the system setup program until you clear the
forgotten password(s).
NOTICE:
The following procedure resets all standard settings for your
computer. Before proceeding, record all current settings so that you can
restore them when you finish this procedure.
1
Turn off the computer and unplug it from the electrical outlet (see
page 20).
2
Open the computer cover (see page 65).
3
Locate the configuration jumper on the system board (see page 68),
and move the jumper plug so that pins 2 and 3 are jumpered (to
“clear” the password when you turn on the computer).
4
Close the computer cover (see page 87), connect your computer to an
electrical outlet, and turn on the computer.
5
Access the system setup program (see page 94) and assign a new
supervisor or setup password in the
Maintenance
menu.
6
Exit and save the system setup program settings.
7
After the computer boots, turn it off, and unplug it from the electrical
outlet.
8
Open the computer cover again.
9
Move the configuration jumper plug so that pins 1 and 2 are jumpered
(the “normal” setting).
10
Close the computer cover, connect your computer to an electrical
outlet, and turn on the computer.