Dell PowerSwitch S5212F-ON EMC SmartFabric OS10 User Guide Release 10.5.0 - Page 1346

listening on e101-003-0, link-type EN10MB (Ethernet), capture size 262144 bytes 01:39:22.457185 IP 3.3.3.1 > 3.3.3.4: ICMP echo request, id 5320, seq 26, length 64 01:39:22.457281 IP 3.3.3.1 > 3.3.3.4: ICMP echo reply, id 5320, seq 26, length 64 Capture two packets from interface $ tcpdump -c 2 -i e101-003-0 listening on e101-003-0, link-type EN10MB (Ethernet), capture size 96 bytes 01:39:22.457185 IP 3.3.3.1 > 3.3.3.4: ICMP echo request, id 5320, seq 26, length 64 01:39:22.457281 IP 3.3.3.1 > 3.3.3.4: ICMP echo reply, id 5320, seq 26, length 64 2 packets captured 13 packets received by filter 0 packets dropped by kernel Capture packets and write to file $ tcpdump -w 06102016.pcap -i e101-003-0 listening on e101-003-0, link-type EN10MB (Ethernet), capture size 96 bytes 32 packets captured 32 packets received by filter 0 packets dropped by kernel Port adapters and modules Use the show diag command to view diagnostics information for OS10 port adapters and hardware modules. View diagnostic hardware information OS10# show diag 00:00.0 Host bridge: Intel Corporation Atom Processor S1200 Internal (rev 02) 00:01.0 PCI bridge: Intel Corporation Atom Processor S1200 PCI Express Root Port 1 (rev 02) 00:02.0 PCI bridge: Intel Corporation Atom Processor S1200 PCI Express Root Port 2 (rev 02) 00:03.0 PCI bridge: Intel Corporation Atom Processor S1200 PCI Express Root Port 3 (rev 02) 00:04.0 PCI bridge: Intel Corporation Atom Processor S1200 PCI Express Root Port 4 (rev 02) 00:0e.0 IOMMU: Intel Corporation Atom Processor S1200 Internal (rev 02) 00:13.0 System peripheral: Intel Corporation Atom Processor S1200 SMBus 2.0 Controller 0 (rev 02) 00:13.1 System peripheral: Intel Corporation Atom Processor S1200 SMBus 2.0 Controller 1 (rev 02) 00:14.0 Serial controller: Intel Corporation Atom Processor S1200 UART (rev 02) 00:1f.0 ISA bridge: Intel Corporation Atom Processor S1200 Integrated Legacy Bus (rev 02) 01:00.0 Ethernet controller: Broadcom Corporation Device b850 (rev 03) 02:00.0 SATA controller: Marvell Technology Group Ltd. Device 9170 (rev 12) 03:00.0 PCI bridge: Pericom Semiconductor PI7C9X442SL PCI Express Bridge Port (rev 02) 04:01.0 PCI bridge: Pericom Semiconductor PI7C9X442SL PCI Express Bridge Port (rev 02) 04:02.0 PCI bridge: Pericom Semiconductor PI7C9X442SL PCI Express Bridge Port (rev 02) 04:03.0 PCI bridge: Pericom Semiconductor PI7C9X442SL PCI Express Bridge Port (rev 02) 07:00.0 USB controller: Pericom Semiconductor PI7C9X442SL USB OHCI Controller (rev 01) 07:00.1 USB controller: Pericom Semiconductor PI7C9X442SL USB OHCI Controller (rev 01) 07:00.2 USB controller: Pericom Semiconductor PI7C9X442SL USB EHCI Controller (rev 01) 08:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection Test network connectivity Use the ping and traceroute commands to test network connectivity. When you ping an IP address, you send packets to a destination and wait for a response. If there is no response, the destination is not active. The ping command is useful during configuration if you have problems connecting to a hostname or IP address. When you execute a traceroute, the output shows the path a packet takes from your device to the destination IP address. It also lists all intermediate hops (routers) that the packet traverses to reach its destination, including the total number of hops traversed. Check IPv4 connectivity OS10# ping 172.31.1.255 Type Ctrl-C to abort. 1346 Troubleshoot Dell EMC SmartFabric OS10