Dell PowerSwitch S5212F-ON EMC SmartFabric OS10 User Guide Release 10.5.0 - Page 77

○ want performs PMTU discovery and fragments large packets locally. ○ dont does not set the Don't Fragment (DF) flag. • -p pattern - (Optional) Enter a maximum of 16 pad bytes to fill out the packet you send to diagnose data-related problems in the network; for example, -p ff fills the sent packet with all 1's. • -Q tos - (Optional) Enter a maximum of 1500 bytes in decimal or hex datagrams to set quality of service (QoS)-related bits. • -s packetsize - (Optional) Enter the number of data bytes to send, from 1 to 65468, default 56. • -S sndbuf - (Optional) Set the sndbuf socket. By default, the sndbuf socket buffers one packet maximum. • -t ttl - (Optional) Enter the IPv4 time-to-live (TTL) value in seconds. • -T timestamp option - (Optional) Set special IP timestamp options. Valid values for timestamp option - tsonly (only timestamps), tsandaddr (timestamps and addresses), or tsprespec host1 [host2 [host3 [host4]]] (timestamp pre-specified hops). • -v - (Optional) Verbose output. • -V - (Optional) Display the version and exit. • -w deadline - (Optional) Enter the time-out value in seconds before the ping exits regardless of how many packets send or receive. • -W timeout - (Optional) Enter the time to wait for a response in seconds. This setting affects the timeout only if there is no response, otherwise ping waits for two round-trip times (RTTs). • hop1 ... (Optional) Enter the IPv4 addresses of the pre-specified hops for the ping packet to take. • destination - Enter the IP address you are testing connectivity on. Default Not configured Command Mode EXEC Usage Information This command uses an ICMP ECHO_REQUEST datagram to receive an ICMP ECHO_RESPONSE from a network host or gateway. Each ping packet has an IPv4 and ICMP header, then a time value and a number of ''pad'' bytes used to fill out the packet. A ping operation sends a packet to a specified IP address and then measures the time that it takes to get a response from the address or device. If the destination IP address is active, replies are sent back from the server including the IP address, number of bytes sent, lapse time in milliseconds, and TTL, which is the number of hops back from the source to the destination. When you use the -I option and enter an IP address, OS10 considers it as the source address. If you use an interface name instead of the IP address, OS10 considers it as the egress interface. With the -I option, if you ping a reachable IP address using the IP address of a loopback interface as the source interface, the ping succeeds. However, if you ping a reachable IP address using the name of the loopback interface as the source interface, the ping fails. This is because the system considers the loopback interface as the egress interface. Example OS10# ping 20.1.1.1 PING 20.1.1.1 (20.1.1.1) 56(84) bytes of data. 64 bytes from 20.1.1.1: icmp_seq=1 ttl=64 time=0.079 ms 64 bytes from 20.1.1.1: icmp_seq=2 ttl=64 time=0.081 ms 64 bytes from 20.1.1.1: icmp_seq=3 ttl=64 time=0.133 ms 64 bytes from 20.1.1.1: icmp_seq=4 ttl=64 time=0.124 ms ^C --- 20.1.1.1 ping statistics --4 packets transmitted, 4 received, 0% packet loss, time 2997ms rtt min/avg/max/mdev = 0.079/0.104/0.133/0.025 ms Supported Releases 10.2.0E or later ping6 Tests network connectivity to an IPv6 device. Syntax ping6 [vrf {management | vrf-name}] [-aAbBdDfhLnOqrRUvV] [-c count] [-i interval] [-I interface] [-l preload] [-m mark] [-M pmtudisc_option] [-N CLI Basics 77