Epson ActionNote 880CX User Manual - Page 124

Fax/Modem Command Set, AT commands continued

Page 124 highlights

AT commands (continued) Command Description x3 Enable extended result codes (O-5, 7, 10) x4 Enable all result codes Y0 Disable long space disconnect Y1 Enable long space disconnect Z0 Software reset; recalls user configuration 0 Z1 Software reset: recalls user configuration 1 &C0 DCD signal always on &C1 DCD signal on when carrier present &DO lgnore DTR signal &D1 Returns to command mode when an on-to-off DTR transition occurs &D2 Hangs up and returns to command mode when an on-to-off DTR transition occurs &D3 Resets when an on-to-off DTR transition occurs &F Loads factory configuration settings &GO No guard tone in CCITT mode &G1 550 Hz guard tone in CClTT mode &G2 1800 Hz guard tone in CClTT mode &Jn Auxiliary relay control &L0 Dial up line &MO Asynchronous communications mode &P0 Pulse dial make/break ratio = 39%/61% (U.S.) &P1 Pulse dial make/break ratio = 33%/67% (U.K.) &Q0 Asynchronous communications mode &Sn Data set ready option &Tn Test command selection &Q6 Normal mode &Y0 Recall user profile 0 at power up &Y1 Recall user profile 1 at power up Ln Transmit level attenuation %Dn DTMF level attenuation %V Load secondary defaults &V Display configuration values and dialog settings &W0 Save storable parameters as user configuration 0 Fax/Modem Command Set B-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139

AT commands (continued)
Command
x3
x4
Y0
Y1
Z0
Z1
&C0
&C1
&DO
&D1
&D2
&D3
&F
&GO
&G1
&G2
&Jn
&L0
&MO
&P0
&P1
&Q0
&Sn
&Tn
&Q6
&Y0
&Y1
Ln
%Dn
%V
&V
&W0
Description
Enable extended result codes (O-5, 7, 10)
Enable all result codes
Disable long space disconnect
Enable long space disconnect
Software reset; recalls user configuration 0
Software reset: recalls user configuration 1
DCD signal always on
DCD signal on when carrier present
lgnore DTR signal
Returns to command mode when an on-to-off DTR transition
occurs
Hangs up and returns to command mode when an on-to-off
DTR transition occurs
Resets when an on-to-off DTR transition occurs
Loads factory configuration settings
No guard tone in CCITT mode
550 Hz guard tone in CClTT mode
1800 Hz guard tone in CClTT mode
Auxiliary relay control
Dial up line
Asynchronous communications mode
Pulse dial make/break ratio = 39%/61% (U.S.)
Pulse dial make/break ratio = 33%/67% (U.K.)
Asynchronous communications mode
Data set ready option
Test command selection
Normal mode
Recall user profile 0 at power up
Recall user profile 1 at power up
Transmit level attenuation
DTMF level attenuation
Load secondary defaults
Display configuration values and dialog settings
Save storable parameters as user configuration 0
Fax/Modem Command Set
B-3