Epson ActionTower 8200 User Manual - Page 78

the Cover. Then see Post-installation Procedures

Get Epson ActionTower 8200 PDF manuals and user guides View all Epson ActionTower 8200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

4. Push the SIMM into the socket until it is seated firmly in the slot. Then tilt it upright, as shown below, guiding the hole at each end of the SIMM over the retaining post at each end of the SIMM socket. If it does not go in smoothly, do not force it; pull it all the way out and try again. 5. Check the settings ofjumpers JP12 (indicating 36-bit SIMMs with parity or 32-bit SIMMs without parity) and JP14 (indicating double- and single-sided SIMMs or single-sided SIMMs only) and change them if necessary. See "Changing the Jumper Settings" for instructions. 6. Replace any option cards you removed; see "Installing an Option Card" for instructions. 7. Replace the computer's cover as described under "Replacing the Cover." Then see "Post-installation Procedures" for instructions on configuring your computer with your new memory size. 4-14 Installing and Removing Options

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
4.
Push the SIMM into the socket until it is seated firmly in the
slot. Then tilt it upright, as shown below, guiding the hole
at each end of the SIMM over the retaining post at each end
of the SIMM socket. If it does not go in smoothly, do not
force it; pull it all the way out and try again.
5.
Check the settings ofjumpers JP12 (indicating 36-bit SIMMs
with parity or 32-bit SIMMs without parity) and JP14
(indicating double- and single-sided SIMMs or single-sided
SIMMs only) and change them if necessary. See “Changing
the Jumper Settings” for instructions.
6.
Replace any option cards you removed; see “Installing an
Option Card” for instructions.
7.
Replace the computer’s cover as described under “Replacing
the Cover." Then see “Post-installation Procedures” for
instructions on configuring your computer with your new
memory size.
4-14
Installing and Removing Options