Fisher and Paykel DE7027P1 User Guide - Page 26

DO NOT use in Canada.

Get Fisher and Paykel DE7027P1 PDF manuals and user guides View all Fisher and Paykel DE7027P1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

24 Installation instructions Connecting the dryer using 3-wire connection Important! ■■ DO NOT use in Canada. ■■ DO NOT use for Mobile home installations, on new constructions, or on recreational vehicles. ■■ NOT for use in areas where local codes prohibit grounding through the neutral conduction. If required by local codes, install an external ground (not provided) to grounded metal, a cold water pipe or other established ground as determined by a qualified electrician. Ground strap Hot wire Green ground screw Screws (2) Neutral (white) Screw Hot wire Fuse Cover Strain relief bracket 120/240V 30 amp power supply cord kit (min length 4 feet (1.5 m)) marked for use with dryers and provided with closed loop or spade terminals with upturned ends (not supplied) 3⁄4" (19 mm), UL recognized strain relief Fig.15 3-wire connections 1 Turn off the circuit breaker(s) (30 amp) or remove the dryer's circuit fuse at the electrical box. 2 Ensure the dryer cord is unplugged from the wall outlet. 3 Locate and remove the power cord cover at the lower rear of the dryer. 4 Install a ¾" (19 mm) UL-recognized strain relief to the entry hole for the power cord. Move the power cord through the strain relief. 5 Connect the power cord according to the following: a Connect the two hot lines to the outer screws of the terminal block (labelled L1 and L2). b Connect the neutral (white) line to the center of the terminal block (labelled N). 6 Ensure the ground strap is connected to neutral (center) terminal of block, and to the green ground screw on located on the cabinet rear. 7 Tighten all three terminal block screws completely. 8 Correctly secure the power cord to the strain relief. 9 Replace the power cord cover. WARNING! NEVER leave the power cord cover off the terminal block.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Installation instructions
24
Connecting the dryer using 3-wire connection
Important!
■
±
DO NOT use in Canada.
■
±
DO NOT use for Mobile home installations, on new constructions, or on recreational vehicles.
■
±
NOT for use in areas where local codes prohibit grounding through the neutral conduction.
Ground strap
If required by local codes, install an external ground (not provided) to grounded metal,
a cold water pipe or other established ground as determined by a qualified electrician.
Hot wire
Strain relief bracket
¹²»” (19 mm), UL recognized strain relief
120/240V 30 amp power supply cord kit (min
length 4 feet (1.5 m)) marked for use with
dryers and provided with closed loop or spade
terminals with upturned ends (not supplied)
Fuse
Cover
Screw
Neutral (white)
Screws (2)
Fig.15 3-wire connections
Hot wire
Green ground screw
1
Turn off the circuit breaker(s) (30 amp) or remove the dryer’s circuit fuse at the electrical box.
2
Ensure the dryer cord is unplugged from the wall outlet.
3
Locate and remove the power cord cover at the lower rear of the dryer.
4
Install a ¾” (19 mm) UL-recognized strain relief to the entry hole for the power cord. Move the
power cord through the strain relief.
5
Connect the power cord according to the following:
a
Connect the two hot lines to the outer screws of the terminal block (labelled L1 and L2).
b
Connect the neutral (white) line to the center of the terminal block (labelled N).
6
Ensure the ground strap is connected to neutral (center) terminal of block, and to the green
ground screw on located on the cabinet rear.
7
Tighten all three terminal block screws completely.
8
Correctly secure the power cord to the strain relief.
9
Replace the power cord cover.
WARNING!
NEVER leave the power cord cover off the terminal block.