Fisher and Paykel DE7027P1 User Guide - Page 42

Ensure you DO NOT OVERTIGHTEN the connections. Overtightening may result in damage to the, couplings

Get Fisher and Paykel DE7027P1 PDF manuals and user guides View all Fisher and Paykel DE7027P1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

40 Installation instructions 4 Check that the washer inlet hose (which has been removed from the faucet) has a flat washer or filter washer fitted. If not insert a flat washer and connect the hose to one of the male couplings on the "Y" connector. 5 Take the long inlet hose and insert a flat washer into the straight female coupling and connect it to the other male coupling on the "Y" connector. 6 Insert a flat rubber washer into the other female connector and couple the hose to the inlet valve on the rear of the dryer. Fig.32 Attaching the inlet hose to the dryer 7 Check that all connections are firmly hand tight, then using a pair of pliers tighten each coupling another two-thirds of a turn. Important! Ensure you DO NOT OVERTIGHTEN the connections. Overtightening may result in damage to the couplings. Fig.33 Tightening the connections 8 Check immediately for any leaks from the "Y" connector, hose couplings and/or the faucet. Check again for leaks after 24 hours.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
40
Installation instructions
4
Check that the washer inlet hose (which has been removed from the faucet) has a flat washer or
filter washer fitted. If not insert a flat washer and connect the hose to one of the male couplings
on the “Y” connector.
5
Take the long inlet hose and insert a flat washer into the straight female coupling and connect it
to the other male coupling on the “Y” connector.
6
Insert a flat rubber washer into the other female connector and couple the hose to the inlet
valve on the rear of the dryer.
Fig.32 Attaching the inlet hose to the dryer
7
Check that all connections are firmly hand tight, then using a pair of pliers tighten each coupling
another two-thirds of a turn.
Important!
Ensure you DO NOT OVERTIGHTEN the connections. Overtightening may result in damage to the
couplings.
Fig.33 Tightening the connections
8
Check immediately for any leaks from the “Y” connector, hose couplings and/or the faucet. Check
again for leaks after 24 hours.