Fisher and Paykel DE7027P1 User Guide - Page 37

Before performing this exhaust installation, be sure to disconnect the dryer from its

Get Fisher and Paykel DE7027P1 PDF manuals and user guides View all Fisher and Paykel DE7027P1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Installation instructions 35 Dryer exhaust to right, left or bottom of cabinet WARNING! Before performing this exhaust installation, be sure to disconnect the dryer from its electrical supply. Protect your hands and arms from sharp edges when working inside the cabinet. Be sure to wear gloves. Important! ■■ Dryer exhaust to right of cabinet (electric models only). ■■ Dryer exhaust to left of cabinet (gas and electric models). Detach and remove the bottom, right or left side knockout (the opening for alternate ducting), as preferred for the direction of ducting. Tape around the knockout and exhaust opening to provide protection from sharp edges during installation. Remove the screw inside the dryer exhaust duct and slide the duct out of the dryer. Keep the screw. Cut the duct as shown in Figure 24. Retain portion A of the duct. Right (electric models only) Fixing hole Remove screw and save 9" (230 mm) Bottom (gas and electric models) Left (gas and electric models) Remove desired knockout (one only) Fig.24 Removing and shortening the duct Tab location Through the rear opening, find the tab located in the middle of the dryer base. Using a flat blade screwdriver, lift the tab to approximately 45°. Bend tab up 45° Fig.25 Lifting the tab

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Installation instructions
35
Dryer exhaust to right, left or bottom of cabinet
WARNING!
Before performing this exhaust installation, be sure to disconnect the dryer from its
electrical supply. Protect your hands and arms from sharp edges when working inside
the cabinet. Be sure to wear gloves.
Important!
■
±
Dryer exhaust to right of cabinet (electric models only).
■
±
Dryer exhaust to left of cabinet (gas and electric models).
Detach and remove the bottom, right or left side knockout (the opening for alternate ducting),
as preferred for the direction of ducting. Tape around the knockout and exhaust opening to
provide protection from sharp edges during installation. Remove the screw inside the dryer
exhaust duct and slide the duct out of the dryer. Keep the screw. Cut the duct as shown in
Figure 24. Retain portion A of the duct.
Right (electric
models only)
Fig.24 Removing and
shortening the duct
Remove desired
knockout (one only)
Remove screw
and save
Bottom (gas
and electric
models)
Left (gas and
electric models)
Fixing hole
9” (230 mm)
Tab location
Through the rear opening, find the tab located in the middle of the dryer base. Using a flat blade
screwdriver, lift the tab to approximately 45°.
Bend tab
up 45°
Fig.25 Lifting the tab