Fisher and Paykel DE7027P1 User Guide - Page 27

Connecting an electric dryer skip for gas dryers - in Canada only, Grounding instructions

Get Fisher and Paykel DE7027P1 PDF manuals and user guides View all Fisher and Paykel DE7027P1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Installation instructions 25 Connecting an electric dryer (skip for gas dryers) - in Canada only Electrical requirements (electric models only) WARNING! Electric Shock Hazard Plug appliance into grounded 4 prong outlet. Failure to do so can result in death or electric shock. Note: the wiring diagram is located in the control console. It is your responsibility to: ■■ Contact a qualified electrical installer. ■■ Ensure the electrical connection is adequate and conforms with Canadian Electrical Code, C22.1 and all local code requirements. ■■ Plug the dryer into, or connect the dryer to an individual branch circuit, which is protected by the correct time delay fuses or circuit breakers. The power supply must be a 4-wire, single phase, 120/240 V, 60Hz, 30 amp circuit. This dryer is supplied with a CSA approved power cord (5 feet (1.52 m) in length, intended for plugging into a 14-30R wall outlet. Ensure the outlet is within reach of the dryer's final location. 4-wire (NEMA type 14-30R) A replacement power cord is available, if required. Use of part number 248C1014G001 (240 V cord set) is recommended. Contact Fisher & Paykel Customer Care (refer to page 84). Grounding instructions This dryer MUST be connected to a grounded metal, permanent wiring system. WARNING! Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the dryer.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Installation instructions
25
Connecting an electric dryer (skip for gas dryers) – in Canada only
Electrical requirements (electric models only)
WARNING!
Electric Shock Hazard
Plug appliance into grounded 4 prong outlet.
Failure to do so can result in death or electric shock.
Note: the wiring diagram is located in the control console.
It is your responsibility to:
■
±
Contact a qualified electrical installer.
■
±
Ensure the electrical connection is adequate and conforms with Canadian Electrical Code, C22.1
and all local code requirements.
■
±
Plug the dryer into, or connect the dryer to an individual branch circuit, which is protected by
the correct time delay fuses or circuit breakers. The power supply must be a 4-wire, single phase,
120/240 V, 60Hz, 30 amp circuit.
This dryer is supplied with a CSA approved power cord (5 feet (1.52 m) in length, intended for
plugging into a 14-30R wall outlet. Ensure the outlet is within reach of the dryer’s final location.
4-wire
(NEMA type 14-30R)
A replacement power cord is available, if required. Use of part number 248C1014G001 (240 V
cord set) is recommended. Contact Fisher & Paykel Customer Care (refer to page 84).
Grounding instructions
This dryer MUST be connected to a grounded metal, permanent wiring system.
WARNING!
Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or service representative if you are
in doubt as to whether the appliance is properly grounded. Do not modify the plug
provided with the dryer.