Foxconn Destroyer English Manual. - Page 38

MCP SATA Mode - driver

Get Foxconn Destroyer PDF manuals and user guides View all Foxconn Destroyer manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

MCP SATA Mode Phoenix - AwardBIOS CMOS Setup Utility MCP SATA Mode SATA Operation Mode x SATA Pri-Master RAID x SATA Pri-Slave RAID x SATA Sec-Master RAID x SATA Sec-Slave RAID x SATA Thi-Master RAID x SATA Thi-Slave RAID [IDE] Item Help Disabled Disabled Menu Level ► Disabled Disabled Disabled Disabled 3 Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F7: Optimized Defaults ► SATA Operation Mode This item is used to set the operating mode of your SATA ports. The available options are: [IDE] - This configures the SATA ports to support legacy PATA mode or SATA mode. [AHCI] - The Advanced Host Controller Interface (AHCI) specification describes the register level interface for a Host Controller for Serial ATA. The specification includes a description of the hardware/software interface between system software and the host controller hardware. AHCI provides more advanced features including SATA features, but some SATA drives may not support AHCI, unless they are labeled with AHCI support in its specification. If your motherboard supporting AHCI, and you have a SATA device, which also supports AHCI, then you can select IDE option to have fair performance (only PATA, SATA level), or you can select AHCI to get its best performance. [Linux AHCI] - For advanced Linux system if it supports AHCI, then you can select this optiion. WARNING! With your motherboard and SATA hard disk both supporting AHCI, you had better set this BIOS setting to AHCI, then install your Operating System (such as Windows XP). Later, if you ever change this BIOS setting to IDE, OS still can run. But if you at the first time set this setting to IDE, then install the Operating System. Later, if you change this BIOS setting to AHCI, this operating system can not run. [RAID] - When you enable RAID, it means all your SATA drives must also support AHCI. ! The Installation procedures for AHCI and RAID drivers are the same, they are : ■ Creating a bootable drive (or RAID array). ■ Creating a non-bootable drive (or RAID array). In Chapter 5, only RAID is introduced. AHCI installation is almost the same, the only difference is BIOS SATA Operation Mode is set to [AHCI] instead of [RAID]. 31 CAUTION

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
31
3
MCP SATA Mode
► SATA Operation Mode
This item is used to set the operating mode of your SATA ports. The available options are:
[IDE] -
This
configures the SATA ports to support legacy PATA mode or SATA mode.
[AHCI] -
The Advanced Host Controller Interface (AHCI) specification describes the register
level interface for a Host Controller for Serial ATA. The specification includes a description of
the hardware/software interface between system software and the host controller hardware.
AHCI provides more advanced features including SATA features, but some SATA drives may
not support AHCI, unless they are labeled with AHCI support in its specification.
If your motherboard supporting AHCI, and you have a SATA device, which also supports AHCI,
then you can select IDE option to have fair performance (only PATA, SATA level), or you can
select AHCI to get its best performance.
[Linux AHCI]
- For advanced Linux system if it supports AHCI, then you can select this optiion.
[RAID] -
When you enable RAID, it means all your SATA drives must also support AHCI.
Phoenix - AwardBIOS CMOS Setup Utility
MCP SATA Mode
SATA Operation Mode
[
]
Item Help
x SATA Pri-Master RAID
Disabled
x SATA Pri-Slave RAID
Disabled
Menu Level
►
x SATA Sec-Master RAID
Disabled
x SATA Sec-Slave RAID
Disabled
x SATA Thi-Master RAID
Disabled
x SATA Thi-Slave RAID
Disabled
↑↓→←:Move
Enter:Select
+/-/PU/PD:Value
F10:Save
ESC:Exit
F1:General Help
F5: Previous Values
F7: Optimized Defaults
IDE
With your motherboard and SATA hard disk both supporting AHCI, you had better set
this BIOS setting to AHCI, then install your Operating System (such as Windows XP).
Later, if you ever change this BIOS setting to IDE, OS still can run.
But if you at the first time set this setting to IDE, then install the Operating System.
Later, if you change this BIOS setting to AHCI, this operating system can not run.
W
A
R
N
I
N
G
!
The Installation procedures for AHCI and RAID drivers are the same, they are :
■
Creating a bootable drive (or RAID array).
■
Creating a non-bootable drive (or RAID array).
In Chapter 5, only RAID is introduced. AHCI installation is almost the same, the only
difference is BIOS SATA Operation Mode is set to [AHCI] instead of [RAID].
CAUTION
!