HP 6125XLG R2306-HP 6125XLG Blade Switch MCE Configuration Guide - Page 15

Configuring static routing between an MCE and a PE, Configuring RIP between an MCE and a PE,

Get HP 6125XLG PDF manuals and user guides View all HP 6125XLG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Configuring static routing between an MCE and a PE Step 1. Enter system view. 2. Configure a static route for a VPN instance. 3. (Optional.) Configure the default preference for static routes. Command system-view ip route-static vpn-instance s-vpn-instance-name dest-address { mask | mask-length } { next-hop-address [ public ] [ track track-entry-number ] | interface-type interface-number [ next-hop-address ] | vpn-instance d-vpn-instance-name next-hop-address [ track track-entry-number ] } [ permanent ] [ preference preference-value ] [ tag tag-value ] [ description description-text ] ip route-static default-preference default-preference-value Remarks N/A By default, no static route is configured. The default setting is 60. Configuring RIP between an MCE and a PE Step Command 1. Enter system view. system-view 2. Create a RIP process for a VPN instance and rip [ process-id ] vpn-instance enter RIP view. vpn-instance-name 3. Enable RIP on the interface attached to the specified network. network network-address 4. Redistribute the VPN routes. import-route protocol [ process-id ] [ allow-ibgp ] [ cost cost | route-policy route-policy-name | tag tag ] * 5. (Optional.) Configure the default cost value for the redistributed routes. default cost value Remarks N/A N/A By default, RIP is disabled on an interface. By default, no route of any other routing protocol is redistributed into RIP. If you do not specify a default cost, the default cost is 0. For more information about RIP, see Layer 3-IP Routing Configuration Guide. Configuring OSPF between an MCE and a PE Step Command 1. Enter system view. system-view 2. Create an OSPF process for a ospf [ process-id | router-id VPN instance and enter OSPF router-id | vpn-instance view. vpn-instance-name ] * 3. Disable routing loop detection. vpn-instance-capability simple Remarks N/A N/A Routing loop detection is enabled. You must disable routing loop detection for a VPN OSPF process on the MCE. Otherwise, the MCE cannot receive OSPF routes from the PE. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
12
Configuring static routing between an MCE and a PE
Step
Command
Remarks
1.
Enter system view.
system-view
N/A
2.
Configure a static route
for a VPN instance.
ip route-static vpn-instance
s-vpn-instance-name
dest-address
{
mask
|
mask-length
} {
next-hop-address
[
public
]
[
track
track-entry-number
] |
interface-type
interface-number
[
next-hop-address
] |
vpn-instance
d-vpn-instance-name
next-hop-address
[
track
track-entry-number
] }
[
permanent
] [
preference
preference-value
]
[
tag
tag-value
] [
description
description-text
]
By default, no static route is
configured.
3.
(Optional.) Configure
the default preference for
static routes.
ip route-static default-preference
default-preference-value
The default setting is 60.
Configuring RIP between an MCE and a PE
Step
Command
Remarks
1.
Enter system view.
system-view
N/A
2.
Create a RIP process for
a VPN instance and
enter RIP view.
rip
[
process-id
]
vpn-instance
vpn-instance-name
N/A
3.
Enable RIP on the
interface attached to
the specified network.
network
network-address
By default, RIP is disabled on
an interface.
4.
Redistribute the VPN
routes.
import-route
protocol
[
process-id
]
[
allow-ibgp
] [
cost
cost
|
route-policy
route-policy-name
|
tag
tag
] *
By default, no route of any
other routing protocol is
redistributed into RIP.
5.
(Optional.) Configure
the default cost value
for the redistributed
routes.
default cost
value
If you do not specify a default
cost, the default cost is 0.
For more information about RIP, see
Layer 3—IP Routing Configuration Guide
.
Configuring OSPF between an MCE and a PE
Step
Command
Remarks
1.
Enter system view.
system-view
N/A
2.
Create an OSPF process for a
VPN instance and enter OSPF
view.
ospf
[
process-id
|
router-id
router-id
|
vpn-instance
vpn-instance-name
] *
N/A
3.
Disable routing loop
detection.
vpn-instance-capability simple
Routing loop detection is enabled.
You must disable routing loop
detection for a VPN OSPF process
on the MCE. Otherwise, the MCE
cannot receive OSPF routes from
the PE.