HP 6125XLG R2306-HP 6125XLG Blade Switch MCE Configuration Guide - Page 35

Configuring routing between an IPv6 MCE and a PE, Configuring IPv6 static routing between an IPv6

Get HP 6125XLG PDF manuals and user guides View all HP 6125XLG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

NOTE: After you configure an IPv6 BGP VPN instance, the IPv6 BGP route exchange for the IPv6 VPN instance is the same as the normal IPv6 BGP VPN route exchange. For more information about IPv6 BGP, see Layer 3-IP Routing Configuration Guide. 2. Configure the VPN site: Step 1. Enter system view. 2. Enter BGP view. 3. Configure the MCE as the EBGP peer. 4. Create and enter BGP IPv6 unicast instance view. 5. Enable BGP to exchange IPv6 unicast routing information with the EBGP peer. 6. (Optional.) Redistribute the IGP routes of the VPN. Command system-view bgp as-number peer ipv6-address as-number as-number ipv6-family [ unicast ] peer ipv6-address enable import-route protocol [ process-id [ med med-value | route-policy route-policy-name ] * ] Remarks N/A N/A By default, no BGP peer is configured. N/A By default, BGP cannot exchange IPv6 unicast routing information with a peer. By default, no route redistribution is configured. A VPN site must advertise the IPv6 VPN network addresses it can reach to the connected IPv6 MCE. Configuring routing between an IPv6 MCE and a PE IPv6 MCE-PE routing configuration includes these tasks: • Binding the IPv6 MCE-PE interfaces to IPv6 VPN instances. • Performing routing configurations. • Redistributing IPv6 VPN routes into the routing protocol running between the IPv6 MCE and the PE. Configurations in this section are performed on the MCE. For information about configuring the PE, see the configuration guide for the PE. Configuring IPv6 static routing between an IPv6 MCE and a PE Step 1. Enter system view. 2. Configure IPv6 static routes for an IPv6 VPN instance. Command system-view ipv6 route-static vpn-instance s-vpn-instance-name ipv6-address prefix-length { interface-type interface-number [ next-hop-address ] | nexthop-address [ public ] | vpn-instance d-vpn-instance-name nexthop-address } [ permanent ] [ preference preference-value ] [ tag tag-value ] [ description description-text ] Remarks N/A By default, no IPv6 static route is configured. 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
32
NOTE:
After you configure an IPv6 BGP VPN instance, the IPv6 BGP route exchange for the IPv6 VPN
instance is the same as the normal IPv6 BGP VPN route exchange. For more information about IPv6
BGP, see
Layer 3—IP Routing Configuration Guide
.
2.
Configure the VPN site:
Step
Command
Remarks
1.
Enter system view.
system-view
N/A
2.
Enter BGP view.
bgp
as-number
N/A
3.
Configure the MCE as the
EBGP peer.
peer
ipv6-address
as-number
as-number
By default, no BGP peer is
configured.
4.
Create and enter BGP IPv6
unicast instance view.
ipv6-family
[
unicast
]
N/A
5.
Enable BGP to exchange
IPv6 unicast routing
information with the EBGP
peer.
peer
ipv6-address
enable
By default, BGP cannot
exchange IPv6 unicast routing
information with a peer.
6.
(Optional.) Redistribute the
IGP routes of the VPN.
import-route
protocol
[
process-id
[
med
med-value
|
route-policy
route-policy-name
]
* ]
By default, no route redistribution
is configured.
A VPN site must advertise the
IPv6 VPN network addresses it
can reach to the connected IPv6
MCE.
Configuring routing between an IPv6 MCE and a PE
IPv6 MCE-PE routing configuration includes these tasks:
•
Binding the IPv6 MCE-PE interfaces to IPv6 VPN instances.
•
Performing routing configurations.
•
Redistributing IPv6 VPN routes into the routing protocol running between the IPv6 MCE and the PE.
Configurations in this section are performed on the MCE. For information about configuring the PE, see
the configuration guide for the PE.
Configuring IPv6 static routing between an IPv6 MCE and a PE
Step
Command
Remarks
1.
Enter system view.
system-view
N/A
2.
Configure IPv6 static
routes for an IPv6 VPN
instance.
ipv6 route-static vpn-instance
s-vpn-instance-name
ipv6-address prefix-length
{
interface-type
interface-number
[
next-hop-address
] |
nexthop-address
[
public
] |
vpn-instance
d-vpn-instance-name nexthop-address
} [
permanent
]
[
preference
preference-value
] [
tag
tag-value
]
[
description
description-text
]
By default, no IPv6
static route is
configured.