HP 6531s HP Compaq 6530s, 6531s and 6535s Notebook PCs - Maintenance and Servi - Page 88

Flex the left side of the base enclosure until the external monitor connector

Get HP 6531s - Notebook PC PDF manuals and user guides View all HP 6531s manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

When replacing the system board, be sure that the following components are removed from the defective system board and installed on the replacement system board: ● Memory module (see Memory module on page 53) ● WLAN module (see WLAN module on page 50) ● Processor (see Processor on page 88) Remove the system board: 1. Remove the RJ-11 connector (1) from the base enclosure clip. 2. Disconnect the Bluetooth module cable (2) and the USB connector module cable (3) from the system board. 3. Remove the Torx T8M2.5×6.0 screw from the system board. 4. Flex the left side of the base enclosure until the external monitor connector (1) and the heat sink (2) are clear of the openings in the base enclosure. 5. Lift the rear edge of the system board (3) until it rests at an angle. 80 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
When replacing the system board, be sure that the following components are removed from the defective
system board and installed on the replacement system board:
●
Memory module (see
Memory module
on page
53
)
●
WLAN module (see
WLAN module
on page
50
)
●
Processor (see
Processor
on page
88
)
Remove the system board:
1.
Remove the RJ-11 connector
(1)
from the base enclosure clip.
2.
Disconnect the Bluetooth module cable
(2)
and the USB connector module cable
(3)
from the
system board.
3.
Remove the Torx T8M2.5×6.0 screw from the system board.
4.
Flex the left side of the base enclosure until the external monitor connector
(1)
and the heat sink
(2)
are clear of the openings in the base enclosure.
5.
Lift the rear edge of the system board
(3)
until it rests at an angle.
80
Chapter 4
Removal and replacement procedures