HP 9000 Superdome SX2000 HP Installation Guide, HP Integrity Superdome/sx2000 - Page 35

Checking Voltage, Wall Receptacle Pinouts, WARNING

Get HP 9000 Superdome SX2000 PDF manuals and user guides View all HP 9000 Superdome SX2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Checking Voltage The voltage check ensures that all phases (and neutral, for international systems) are wired correctly for the cabinet and that the AC input voltage is within specified limits. NOTE: If you use a UPS, see applicable UPS documentation for information to connect the server and to check the UPS output voltage. UPS User Manual documentation is shipped with the UPS and is available at www.hp.com/go/bizsupport. 1. Verify that site power is OFF. 2. Open the site circuit breakers. 3. Verify that the receptacle ground connector is connected to ground. See Figure 30 for connector details. 4. Set the site power circuit breaker to ON. Figure 30 Wall Receptacle Pinouts 5. Verify that the voltage between receptacle pins x and y is 200-240 volts ac. 6. Set the site power circuit breaker to OFF. 7. Ensure that power is removed from the server. 8. Route and connect the server power connector to the site power receptacle. • For locking type receptacles, line up the key on the plug with the groove in the receptacle. • Push the plug into the receptacle and rotate to lock the connector in place. WARNING! Do not set site ac circuit breakers serving the processor cabinets to ON before verifying that the cabinet has been wired into the site ac power supply correctly. Failure to do so can result in injury to personnel or damage to equipment when ac power is applied to the cabinet. 9. Set the site power circuit breaker to ON. WARNING! There is a risk of shock hazard while testing primary power. Use properly insulated probes. Be sure to replace the access cover when you finish testing primary power. 10. Set the server power to ON. Setting Up the System 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
Checking Voltage
The voltage check ensures that all phases (and neutral, for international systems) are wired correctly
for the cabinet and that the AC input voltage is within specified limits.
NOTE:
If you use a UPS, see applicable UPS documentation for information to connect the server
and to check the UPS output voltage. UPS User Manual documentation is shipped with the UPS
and is available at w
w
w
.hp
.co
m/go/b
i
zsu
ppo
r
t
.
1.
Verify that site power is
OFF
.
2.
Open the site circuit breakers.
3.
Verify that the receptacle ground connector is connected to ground. See
Figure 30
for connector
details.
4.
Set the site power circuit breaker to
ON
.
Figure 30 Wall Receptacle Pinouts
5.
Verify that the voltage between receptacle pins x and y is 200–240 volts ac.
6.
Set the site power circuit breaker to
OFF
.
7.
Ensure that power is removed from the server.
8.
Route and connect the server power connector to the site power receptacle.
•
For locking type receptacles, line up the key on the plug with the groove in the receptacle.
•
Push the plug into the receptacle and rotate to lock the connector in place.
WARNING!
Do not set site ac circuit breakers serving the processor cabinets to
ON
before
verifying that the cabinet has been wired into the site ac power supply correctly. Failure to
do so can result in injury to personnel or damage to equipment when ac power is applied to
the cabinet.
9.
Set the site power circuit breaker to
ON
.
WARNING!
There is a risk of shock hazard while testing primary power. Use properly
insulated probes. Be sure to replace the access cover when you finish testing primary power.
10. Set the server power to
ON
.
Setting Up the System
35