HP BladeSystem bc2800 Service Reference Guide: HP BladeSystem PC Blade Enclosu - Page 29

Midplane Assembly, Integrated Administrator security settings are assigned to HP PC Blade Enclosure

Get HP BladeSystem bc2800 - Blade PC PDF manuals and user guides View all HP BladeSystem bc2800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Midplane Assembly To remove the midplane assembly: 1. Power down each HP Blade PC (Powering Down a Blade PC on page 12). 2. Power down the enclosure (Powering Down the Enclosure on page 10). 3. Disconnect all cables and power cords from the AC power source. 4. Disconnect all cables and power cords from the enclosure rear panel. 5. Remove all HP Blade PCs (Removing a Blade PC on page 13). CAUTION: Integrated Administrator security settings are assigned to HP PC Blade Enclosure bays, not to HP Blade PCs. If HP Blade PCs change locations within the enclosure, Integrated Administrator settings must also be adjusted to ensure accurate security. Refer to the HP Integrated Administrator User Guide for more information on security settings. 6. Remove both hot-plug power supplies (Hot-Plug Power Supplies on page 8). 7. Remove the interconnect tray from the enclosure (Removing the Interconnect Tray on page 15). 8. Remove the enclosure from the rack (Removing the HP PC Blade Enclosure from the Rack on page 16). 9. Place the enclosure on a level, non-conductive surface. 10. Open the access door (Opening the Access Door on page 17). 11. Disconnect the fan cable from the midplane (power board) (Fan Backplane Assembly on page 19). 12. Disconnect the enclosure status cable from the midplane (signal board) (Enclosure Status Assembly on page 21). 13. Loosen the thumbscrews on the midplane assembly (1). Non-Hot-Plug Procedures 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
Midplane Assembly
To remove the midplane assembly:
1.
Power down each HP Blade PC (
Powering Down a Blade PC
on page
12
).
2.
Power down the enclosure (
Powering Down the Enclosure
on page
10
).
3.
Disconnect all cables and power cords from the AC power source.
4.
Disconnect all cables and power cords from the enclosure rear panel.
5.
Remove all HP Blade PCs (
Removing a Blade PC
on page
13
).
CAUTION:
Integrated Administrator security settings are assigned to HP PC Blade Enclosure
bays, not to HP Blade PCs. If HP Blade PCs change locations within the enclosure, Integrated
Administrator settings must also be adjusted to ensure accurate security. Refer to the HP
Integrated Administrator User Guide
for more information on security settings.
6.
Remove both hot-plug power supplies (
Hot-Plug Power Supplies
on page
8
).
7.
Remove the interconnect tray from the enclosure (
Removing the Interconnect Tray
on page
15
).
8.
Remove the enclosure from the rack (
Removing the HP PC Blade Enclosure from the Rack
on page
16
).
9.
Place the enclosure on a level, non-conductive surface.
10.
Open the access door (
Opening the Access Door
on page
17
).
11.
Disconnect the fan cable from the midplane (power board) (
Fan Backplane Assembly
on page
19
).
12.
Disconnect the enclosure status cable from the midplane (signal board) (
Enclosure Status
Assembly
on page
21
).
13.
Loosen the thumbscrews on the midplane assembly
(1)
.
Non-Hot-Plug Procedures
23