HP J9146A Installation Guide - Page 40

(Optional) Install a Transceiver, To remove the transceiver: - support

Get HP J9146A - ProCurve Switch 2910al-24G-PoE PDF manuals and user guides
UPC - 884420766971
View all HP J9146A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Installing the Switch Installation Procedures 5. (Optional) Install a Transceiver Note Hot swapping transceivers is supported. You can install or remove a transceiver with the switch powered on, a reset will not occur. However, rapid hotswaps are not recommended. Wait 5 seconds between hotswaps. a. Slide the transceiver in until it stops. b. Push firmly until the gasket seats against the bulkhead. Installing the Switch Note Bail Figure 2-11. Installing a transceiver When switch power is on, the Link and Activity LEDs will come on for approximately two seconds and then go off. This is confirmation the transceiver is completely seated. c. If your transceiver has a bail, move the bail up, if not your transceiver is now completely installed. To remove the transceiver: If your transceiver has a bail, lower the bail until it is approximately horizontal, and then using the bail, pull the transceiver from the slot. If your transceiver does not have a bail, pull the transceiver straight out. 2-14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
2-14
Installing the Switch
Installation Procedures
Installing the Switch
5. (Optional) Install a Transceiver
Note
Hot swapping transceivers is supported. You can install or remove a
transceiver with the switch powered on, a reset will not occur. However, rapid
hotswaps are not recommended. Wait 5 seconds between hotswaps.
a.
Slide the transceiver in until it stops.
b.
Push firmly until the gasket seats against the bulkhead.
Figure 2-11.
Installing a transceiver
Note
When switch power is on, the Link and Activity LEDs will come on for
approximately two seconds and then go off. This is confirmation the
transceiver is completely seated.
c.
If your transceiver has a bail, move the bail up, if not your transceiver is
now completely installed.
To remove the transceiver:
If your transceiver has a bail, lower the bail until it is approximately horizontal,
and then using the bail, pull the transceiver from the slot. If your transceiver
does not have a bail, pull the transceiver straight out.
Bail