HP J9146A Installation Guide - Page 9

1 Introducing the Switch Introducing the Switch Power Fault Locator Console ProCurve Switch 2910bl-24G J9145A Mdl * Spd mode: RPS Status of the Back off = 10 Mbps 2 flash = 100 Mbps Status Tmp LED Mode Fan Act FDx Spd * on = 1 Gbps 3 flash = 10 Gbps Test Usr Reset Clear Auxiliary Port The HP ProCurve 2910al Switches are multiport switches that can be used to build high-performance switched networks. These switches are store-andforward devices offering low latency for high-speed networking. The 2910al switches also support Redundant Power Supply and Power over Ethernet technologies. HP ProCurve 2910al-24G Switch (J9145A) 10/100/1000Base-T Ports (1 - 24T) — Ports are Auto-MDIX Dual-Personality Ports: 10/100/1000-T (T) or SFP (S) Link 1 Mode 3 5 7 9 11 Link 13 Mode 15 17 19 21T 23T Link 21S Mode 23S ! Use only one (T or S) for each Port Link 2 Mode 4 6 8 10 12 Link 14 Mode 16 18 20 22T 24T Link 22S Mode 24S HP ProCurve 2910al-48G Switch (J9147A) ! Use only one (T or S) for each Port ProCurve Switch Mdl * RPS Status of the Back Spd mode: off=10 Mbps, 2 flash=100 Mbps, on=1 Gbps, 3 flash=10 Gbps 10/100/1000Base-T Ports (1 - 48T) — Ports are Auto-MDIX 2910bl-48G Link 1 Mode 3 5 7 9 11 Link 13 Mode 15 17 19 21 23 Link 25 Mode 27 29 31 33 35 Power Fault Locator J9147A Status Tmp LED Mode Fan Test Act FDx Spd * Usr Console Reset Clear Link 2 Mode 4 6 8 10 12 Link 14 Mode 16 18 20 22 24 Link 26 Mode 28 30 32 34 36 Dual-Personality Ports: 10/100/1000-T (T) or SFP (S) Link 37 Mode 39 41 43 45T 47T Link 45S Mode 47S Link 38 Mode 40 42 44 46T 48T Link 46S Mode 48S Power Fault Locator Console ProCurve Switch 2910bl-24G-PoE Mdl EPS RPS Status of the Back J9146A PoE+ * Spd mode: Status PoE LED Tmp Mode Act FDx Spd * off = 10 Mbps 2 flash = 100 Mbps on = 1 Gbps 3 flash = 10 Gbps Fan PoE Test Usr Reset Clear Auxiliary Port HP ProCurve 2910al-24G-PoE+ Switch (J9146A) PoE+ Integrated 10/100/1000Base-T Ports (1 - 24T) — Ports are Auto-MDIX Dual-Personality Ports: 10/100/1000-T (T) or SFP (S) Link 1 Mode 3 5 7 9 11 Link 13 Mode 15 17 19 21T 23T Link 21S Mode 23S ! Use only one (T or S) for each Port Link 2 Mode 4 6 8 10 12 Link 14 Mode 16 18 20 22T 24T Link 22S Mode 24S HP ProCurve 2910al-48G-PoE+ Switch (J9148A) ! Use only one (T or S) for each Port * ProCurve Switch Mdl EPS RPS Status of the Back Spd mode: off=10 Mbps, 2 flash=100 Mbps, on=1 Gbps, 3 flash=10 Gbps PoE+ Integrated 10/100/1000Base-T Ports (1 - 48T) — Ports are Auto-MDIX 2910bl-48G-PoE Link 1 Mode 3 5 7 9 11 Link 13 Mode 15 17 19 21 23 Link 25 Mode 27 29 31 33 35 Power J9148A PoE+ Fault Locator Status PoE LED Tmp Mode Act FDx Spd * Fan PoE Test Usr Console Reset Clear Link 2 Mode 4 6 8 10 12 Link 14 Mode 16 18 20 22 24 Link 26 Mode 28 30 32 34 36 Dual-Personality Ports: 10/100/1000-T (T) or SFP (S) Link 37 Mode 39 41 43 45T 47T Link 45S Mode 47S Link 38 Mode 40 42 44 46T 48T Link 46S Mode 48S Throughout this manual, these switches will be referred to as the 2910al Switches or the 2910al-PoE+ Switches. 1-1