HP Pro 2080 Maintenance & Service Guide: HP Pro 2000/2080 Business PC - Page 54

Removing an Internal 3.5-inch Hard Drive, Start, HP Backup and Recovery - mt drivers

Get HP Pro 2080 - Microtower PC PDF manuals and user guides View all HP Pro 2080 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

7. Slide the drive in through the front of the chassis (1) until the bezel on the drive is evenly aligned with the computer front bezel and install the two M3 metric retainer screws (2) as shown in the illustration below. NOTE: Extra drive retainer screws are provided on the interior of the front bezel if needed. The M3 metric retainer screws for diskette drives or media card readers are black. Refer to Installing Additional Drives on page 40 for an illustration of the retainer screws location. Figure 6-21 Installing a 3.5-inch Device (Media Card Reader Shown) 8. Connect the appropriate drive cables: a. If installing a diskette drive (available on some models only), connect the power and data cables to the rear of the drive and connect the other end of the data cable to the connector on the system board. b. If installing a media card reader, connect the USB cable from the media card reader to the USB connector on the system board. 9. Replace the front bezel and access panel. 10. Reconnect the power cord and turn on the computer. 11. Lock any security devices that were disengaged when the access panel was removed. Removing an Internal 3.5-inch Hard Drive NOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive. Also, if you are replacing the primary hard drive, make sure you have created a Recovery Disc Set to restore the operating system, software drivers, and any software applications that were preinstalled on the computer. If you do not have this CD set, select Start > HP Backup and Recovery and create it now. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 25). 2. Remove the access panel (Access Panel on page 26). 46 Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
7.
Slide the drive in through the front of the chassis
(1)
until the bezel on the drive is evenly aligned
with the computer front bezel and install the two M3 metric retainer screws
(2)
as shown in the
illustration below.
NOTE:
Extra drive retainer screws are provided on the interior of the front bezel if needed. The
M3 metric retainer screws for diskette drives or media card readers are black. Refer to
Installing
Additional Drives
on page
40
for an illustration of the retainer screws location.
Figure 6-21
Installing a 3.5-inch Device (Media Card Reader Shown)
8.
Connect the appropriate drive cables:
a.
If installing a diskette drive (available on some models only), connect the power and data
cables to the rear of the drive and connect the other end of the data cable to the connector
on the system board.
b.
If installing a media card reader, connect the USB cable from the media card reader to the
USB connector on the system board.
9.
Replace the front bezel and access panel.
10.
Reconnect the power cord and turn on the computer.
11.
Lock any security devices that were disengaged when the access panel was removed.
Removing an Internal 3.5-inch Hard Drive
NOTE:
Before you remove the old hard drive, be sure to back up the data from the old hard drive so
that you can transfer the data to the new hard drive. Also, if you are replacing the primary hard drive,
make sure you have created a Recovery Disc Set to restore the operating system, software drivers,
and any software applications that were preinstalled on the computer. If you do not have this CD set,
select
Start
>
HP Backup and Recovery
and create it now.
1.
Prepare the computer for disassembly (
Preparation for Disassembly
on page
25
).
2.
Remove the access panel (
Access Panel
on page
26
).
46
Chapter 6
Removal and Replacement Procedures Microtower (MT) Chassis