HP Pro 2080 Maintenance & Service Guide: HP Pro 2000/2080 Business PC - Page 58

Installing an Internal 3.5-inch Hard Drive, on Installing, Additional Drives

Get HP Pro 2080 - Microtower PC PDF manuals and user guides View all HP Pro 2080 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Installing an Internal 3.5-inch Hard Drive 1. Follow the steps in Removing an Internal 3.5-inch Hard Drive on page 46 to remove the hard drive cage and, if necessary, the existing hard drive. 2. Slide the new drive into the hard disk drive cage (1), aligning the drive with the four screw holes on the cage. Install the four 6-32 standard screws that secure the hard disk drive to the hard disk drive cage (2). Make sure the hard disk drive cables are facing the top of the drive cage. NOTE: If you are replacing an old drive with a new drive, use the four retainer screws from the old drive to install the new drive. NOTE: If you are installing a second hard drive, use four of the extra standard 6-32 screws that are installed on the interior of the front bezel. The 6-32 screws are silver. Refer to Installing Additional Drives on page 40 for an illustration of the retainer screws location. Figure 6-27 Installing the Hard Drive in the Drive Cage 50 Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
Installing an Internal 3.5-inch Hard Drive
1.
Follow the steps in
Removing an Internal 3.5-inch Hard Drive
on page
46
to remove the hard
drive cage and, if necessary, the existing hard drive.
2.
Slide the new drive into the hard disk drive cage
(1)
, aligning the drive with the four screw holes
on the cage. Install the four 6-32 standard screws that secure the hard disk drive to the hard disk
drive cage
(2)
. Make sure the hard disk drive cables are facing the top of the drive cage.
NOTE:
If you are replacing an old drive with a new drive, use the four retainer screws from the
old drive to install the new drive.
NOTE:
If you are installing a second hard drive, use four of the extra standard 6-32 screws that
are installed on the interior of the front bezel. The 6-32 screws are silver. Refer to
Installing
Additional Drives
on page
40
for an illustration of the retainer screws location.
Figure 6-27
Installing the Hard Drive in the Drive Cage
50
Chapter 6
Removal and Replacement Procedures Microtower (MT) Chassis