Home » HP Manuals » Desktops » HP XM600 » Manual Viewer

HP XM600 hp kayak xm600 series 2, user's guide for minitower models - Page 23

HP Kayak XM600 PC Workstation System Board

Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation HP Kayak XM600 PC Workstation System Board Memory modules supporting two RDRAM modules Up to six accessory cards can be installed: - One Universal AGP PRO (graphics) - Five 32-bit PCI slots Support for one or two processors Primary IDE Connector Floppy Disk Drive Connector Secondary IDE Connector 23

Section	Page
Notice	5
Important Warnings	6
Avoid Electrical Shocks	6
Electrical	6
Multimedia Models	6
Removing and Replacing the Cover	6
Safety Information	7
Unpacking Your PC Workstation	7
Static Electricity	7
Information and Help	8
On HP’s Web Site	9
Downloadable Documentation from HP’s Web Site	9
Information on Ergonomic Aspects	9
Technical Information	10
Physical characteristics (standard configuration as shipped)	10
1 Setting Up and Using Your PCWorkstation	11
Connecting Devices	12
The MaxiLife Status Panel	13
Starting and Stopping Your PC Workstation	14
Starting Your PC Workstation for the First Time	14
Starting Your PC Workstation	14
Initializing Your Software	15
Creating an Emergency Repair Disk	15
Stopping Your PC Workstation	15
Using Your HP Enhanced Multimedia Keyboard (some models only)	16
Viewing the HP Summary Screen	17
Using the HP Setup Program	18
Starting the HP Setup Program	18
Main Menu	18
Advanced Menu	18
Security Menu	19
Boot Menu	19
Power Menu	19
Setting Passwords in the HP Setup Program	20
Setting a Password	20
Using Power Management	21
Manageability	21
Software and Drivers	21
2 Installing and Replacing Hardware Parts in Your PCWorkstation	22
HP Kayak XM600 PC Workstation System Board	23
Removing and Replacing the Cover and Front Bezel	24
Removing the Cover	24
Removing the Front Bezel	25
Replacing the Cover and Front Bezel	25
Replacing or Installing a Processor	26
Removing an Existing Processor	26
Installing a Processor	26
Configuring the Operating System for use with Dual Processors	28
Configuring Windows 2000	28
Configuring Windows NT 4.0 using HP DualExpress!	28
Removing, Replacing and Upgrading Memory	29
Upgrading Memory	29
Removing and Installing a Memory Module	29
Removing and Replacing an Accessory Card	31
Installing Mass Storage Devices	32
Refer to the drive’s manual to see if you must set jumpers or if there is a special installation ...	32
Cables and Connectors (all models)	32
Cables and Connectors (SCSI Models)	34
Power Connectors	35
Additional Guide Rails	35
Removing and Replacing the Primary Hard Disk Drive	36
Installing a Second Hard Disk Drive in an Internal Shelf	37
Installing a Third or a Fourth Hard Disk Drive	38
Installing a Device in a Front Access Bay	39
Replacing the CD-ROM Drive (or DVD-Drive)	41
Replacing the Floppy Disk Drive	42
Completing the Installation of a Mass Storage Device	43
Replacing the Power Supply Unit	44
Replacing the System Board	45
Removing the System Board	45
Installing the New System Board	46
Replacing the Main Chassis Fan	47
Removing the Fan	47
Replacing the Rear Fan	47
Replacing the Fan and Speaker Assembly	48
System Board Switches	49
Replacing the Battery	50
3 Troubleshooting Your HP PCWorkstation	51
If Your PC Does Not Start Properly	52
If Your PC Has a Hardware Problem	52
Using HP MaxiLife to Diagnose Problems	54
Other Features	55
Pre-Boot Diagnostics	58
If You Miss the Beep Code	58
HP eDiagTools Hardware Diagnostics Utility	59
Where Can I Get HP eDiagTools?	59
Before Using HP eDiagTools	59
Starting HP eDiagTools	59
Producing a Support Ticket	60
Image Creation and Recovery CD-ROM	61
Requirements	61
Performing a Recovery, Upgrade or Downgrade	62
Running HP eDiagTools	62
Performing a Full Recovery	62
Completing a Full Recovery	63
Minimal Recovery	63
Performing a Partial Recovery	63
Frequently Asked Questions	64
Collecting Information Before Contacting HP Support	66