HP XM600 hp kayak xm600 series 2, user's guide for minitower models - Page 46

Installing the New System Board

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Replacing the System Board Installing the New System Board 1 Clip the retaining bracket onto the new system board. 2 Aligning the rear connectors with their corresponding sockets, insert the system board and lower it onto the guide pins. Ensure that all hooks are correctly positioned. Check that the rear connectors are correctly aligned in their sockets. 3 Tighten the screw located on the rear panel near the AGP PRO slot to secure the system board in place. 4 Attach the system board to the chassis using the four screws located near the processor sockets.   …  5 Reconnect any cables you disconnected earlier from the system board. To find out the positions of system board connectors, refer to the label located on the inside of the cover. 6 Replace the main memory, processor and any accessory cards in the new system board (described in this chapter). 7 Replace the retaining bar and secure it in place with the retaining screw. 8 Return the PC Workstation to its upright position. 9 Replace the PC Workstation's cover (refer to page 25). Reconnect all the power and telecommunications cables. 10 After installing the system board, you need to update your BIOS. NOTE The latest BIOS for your PC and instructions on updating the BIOS are available from: www.hp.com/go/kayaksupport. 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
2
Installing and Replacing Hardware Parts in Your PC Workstation
Replacing the System Board
46
Installing the New System Board
1
Clip the retaining bracket onto the new system board.
2
Aligning the rear connectors with their corresponding sockets, insert the
system board and lower it onto the guide pins. Ensure that all hooks are
correctly positioned. Check that the rear connectors are correctly
aligned in their sockets.
3
Tighten the screw located on the rear panel near the AGP PRO slot to
secure the system board in place.
4
Attach the system board to the chassis using the four screws located
near the processor sockets.
5
Reconnect any cables you disconnected earlier from the system board.
To find out the positions of system board connectors, refer to the label
located on the inside of the cover.
6
Replace the main memory, processor and any accessory cards in the new
system board (described in this chapter).
7
Replace the retaining bar and secure it in place with the retaining screw.
8
Return the PC Workstation to its upright position.
9
Replace the PC Workstation’s cover (refer to page 25). Reconnect all the
power and telecommunications cables.
10
After installing the system board, you need to update your BIOS.
NOTE
The latest BIOS for your PC and instructions on updating the BIOS are
available from:
www.hp.com/go/kayaksupport
.
´
±
²