HP XM600 hp kayak xm600 series 2, user's guide for minitower models - Page 42

Replacing the Floppy Disk Drive, Removing the, Floppy Disk Drive, Installing the Floppy, Disk Drive

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Replacing the Floppy Disk Drive Removing the Floppy Disk Drive Replacing the Floppy Disk Drive 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover and front upper bezel (refer to page 25 for these instructions). 3 Disconnect the power and data cables from the old drive. 4 Remove the drive. To do this, press the two front clips inward and, pushing from the rear, slide out the drive. 5 Remove the two short green guide rails by gently prying them off the drive. These guide rails will be required for the new drive.  ™ Installing the Floppy Disk Drive 1 Add the short green guide rails to the new drive. Insert the guide rail labeled "L" on the left-hand side (cable connectors facing towards you and positioned at the top), and the guide rail "R" on the right-hand side of the hard disk drive. 2 Align the guide rails on both sides of the drive with the internal shelf guides, then slide the drive until it clicks into position. 3 Connect the power and data cables to the new drive and any installed drives. The connectors are shaped to go in one way only. 4 Replace the front bezel and PC Workstation's cover (refer to page 25). Reconnect all the power and telecommunications cables. 5 Turn to page 43 to complete the installation. 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
2
Installing and Replacing Hardware Parts in Your PC Workstation
Replacing the Floppy Disk Drive
42
Replacing the Floppy Disk Drive
Removing the
Floppy Disk Drive
1
Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2
Remove the PC Workstation’s cover and front upper bezel (refer to page
25 for these instructions).
3
Disconnect the power and data cables from the old drive.
4
Remove the drive. To do this, press the two front clips inward and,
pushing from the rear, slide out the drive.
5
Remove the two short green guide rails by gently prying them off the
drive. These guide rails will be required for the new drive.
Installing the Floppy
Disk Drive
1
Add the short green guide rails to the new drive. Insert the guide rail
labeled “L” on the left-hand side (cable connectors facing towards you
and positioned at the top), and the guide rail “R” on the right-hand side
of the hard disk drive.
2
Align the guide rails on both sides of the drive with the internal shelf
guides, then slide the drive until it clicks into position.
3
Connect the power and data cables to the new drive and any installed
drives.
The connectors are shaped to go in one way only
.
4
Replace the front bezel and PC Workstation’s cover (refer to page 25).
Reconnect all the power and telecommunications cables.
5
Turn to page 43 to complete the installation.
²