Honeywell VISTAKEY User Guide - Page 11

User Code + # + 77

Get Honeywell VISTAKEY PDF manuals and user guides View all Honeywell VISTAKEY manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

User Commands (cont'd) Enter the #77 command as follows: User Code + # + 77 The following message is displayed on the keypad: ACTION ? Enter the two-digit Action Number that RELAY ON 01 corresponds to the action desired. The action codes are the events that are to take place immediately. Each action also requires an action specifier, which defines what the action will affect (relay, relay group, partition, zone list, user group). The action specifier varies, depending on the type of action selected. Table 1: Action Codes provides a listing of the "Action Codes" (desired actions) and describes their related specifiers. NOTE: Action codes 60 (AP Exit Only), 66 (AP Group Exit Only), or 72 (AP Partition Exit Only) disable the entry reader at the access point. The reader will remain disabled until a command is received (via a keypad command or event) to protect the access point. Press the [*] key to accept the entry. An additional keypad prompt appears where you enter the specifier (i.e., relay number, partition number, etc.) for the action entered. Enter the specifier for the action selected. Press the [*] key to accept the entry. The following message is displayed on the keypad: ↓ Action Number 01 Are You Sure? 1=YES 0=NO Press 1 to accept your entries for action and 0 action specifier, or press 0 to cancel your entries. - 11 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
User Commands (cont’d)
– 11 –
Enter the #77 command as follows:
User Code + # + 77
The following message is displayed on the keypad:
ACTION ?
RELAY ON
01
Enter
the
two-digit
Action
Number
that
corresponds to the action desired.
The action codes are the events that are to take
place immediately. Each action also requires an
action specifier, which defines what the action
will affect (relay, relay group, partition, zone
list, user group). The action specifier varies,
depending on the type of action selected.
Table 1: Action Codes
provides a listing of the
“Action Codes” (desired actions) and describes
their related specifiers.
NOTE:
Action codes 60 (AP Exit Only), 66 (AP
Group Exit Only), or 72 (AP Partition Exit Only)
disable the entry reader at the access point. The
reader will remain disabled until a command is
received (via a keypad command or event) to
protect the access point.
Press the [*] key to accept the entry.
An additional keypad prompt appears where
you enter the specifier
(i.e., relay number,
partition number, etc.) for the action entered.
Enter the specifier for the action selected.
Press the [*] key to accept the entry. The
following message is displayed on the keypad:
↓
Action Number
01 Are You Sure?
1=YES 0=NO
0
Press
1
to accept your entries for action and
action specifier, or press
0
to cancel your
entries.