Insignia NS-42LCD User Manual (English) - Page 24

Memorizing channels

Get Insignia NS-42LCD PDF manuals and user guides View all Insignia NS-42LCD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Insignia NS-42LCD 42-inch LCD TV Memorizing channels When you turn on the TV for the first time, you should perform an auto channel search to set up stations on your TV. Before you perform an auto search, you should select the correct TV source. Selecting the TV source Before your TV can memorize the available channels, you must specify the type of signal source that is connected to the TV. (For example, an antenna or cable system.) To select a source: 1 In single window status (with no picture-in-picture setting active), press MENU to display the Main Menu. Note If a picture-in-picture mode is active, your TV cannot do an auto search. 2 Press or to display the CHANNEL SETUP menu page, then press to enter the menu. If TV Source is set to CABLE, highlight Auto Search, then press or . The Channel Scan Source window opens.Press or to select STD (the most common type of Cable TV), HRC, or IRC, then press OK to begin the auto channel search. The TV begins searching for all available CATV or CADTV channels. Note If you want to stop the auto search, press MENU. Skipping channels After saving channels into memory, you can skip unnecessary channels so that only the channels you want to watch are selected with the CH+/buttons. To skip channels: 1 Open the CHANNEL SETUP menu. 3 Press or to select TV Source, then press or to select AIR or CABLE. • Select AIR if using an antenna. • Select CABLE if using Cable TV. Auto channel search You should perform an auto search to search for available broadcast and cable/set-top box channels. After the TV finishes searching for channels, the TV stores the valid channels in memory. • If TV Source is set to AIR, highlight Auto Search, then press or . The TV begins searching for all available TV or DTV channels. 2 Highlight Current Channel, then press or to select an unwanted channel. 3 Highlight Channel Skip, then press or to change the setting to ON. 4 If you want to skip other unwanted channels, repeat Steps 2-3. 5 Press EXIT to exit. The channels you specified will be skipped the next time you press the CH+/- buttons. - OR - 24 www.insignia-products.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
24
Insignia NS-42LCD 42-inch LCD TV
www.insignia-products.com
Memorizing channels
When you turn on the TV for the first time, you
should perform an auto channel search to set up
stations on your TV. Before you perform an auto
search, you should select the correct TV source.
Selecting the TV source
Before your TV can memorize the available
channels, you must specify the type of signal
source that is connected to the TV. (For
example, an antenna or cable system.)
To select a source:
1
In single window status (with no
picture-in-picture setting active), press
MENU
to display the Main Menu.
2
Press
or
to display the CHANNEL
SETUP menu page, then press
to enter
the menu.
3
Press
or
to select
TV Source
, then
press
or
to select
AIR
or
CABLE
.
•
Select
AIR
if using an antenna.
•
Select
CABLE
if using Cable TV.
Auto channel search
You should perform an auto search to search for
available broadcast and cable/set-top box
channels. After the TV finishes searching for
channels, the TV stores the valid channels in
memory.
•
If
TV Source
is set to
AIR
, highlight Auto
Search, then press
or . The TV begins
searching for all available TV or DTV
channels.
- OR -
If
TV Source
is set to
CABLE
, highlight
Auto
Search
, then press
or . The Channel
Scan Source window opens.Press
or
to
select
STD
(the most common type of
Cable TV),
HRC
, or
IRC
, then press
OK
to
begin the auto channel search. The TV
begins searching for all available CATV or
CADTV channels.
Skipping channels
After saving channels into memory, you can skip
unnecessary channels so that only the channels
you want to watch are selected with the CH+/-
buttons.
To skip channels:
1
Open the CHANNEL SETUP menu.
2
Highlight
Current Channel
, then press
or
to select an unwanted channel.
3
Highlight
Channel Skip
, then press
or
to
change the setting to
ON
.
4
If you want to skip other unwanted channels,
repeat Steps 2-3.
5
Press
EXIT
to exit. The channels you
specified will be skipped the next time you
press the CH+/- buttons.
Note
If a picture-in-picture mode is active, your TV
cannot do an auto search.
Note
If you want to stop the auto search, press
MENU
.