Intel D848PMB Technical Product Specification - Page 39

Fan Connectors, 12.2.3, LAN Wake Capabilities, CAUTION

Get Intel D848PMB PDF manuals and user guides View all Intel D848PMB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Product Description 1.12.2.2 Fan Connectors Table 11 summarizes the function/operation of the fan connectors. Table 11. Fan Connector Function/Operation Connector Processor fan Front chassis fan Rear chassis fan Description • +12 V DC connection for a processor fan or active fan heatsink. • Fan is on in the S0 or S1 state. Fan is off when the system is off or in the S3, S4, or S5 state. • Wired to a fan tachometer input of the hardware monitoring and fan control ASIC. • Closed-loop fan control (optional) that can adjust the fan speed or switch the fans on or off as needed. • +12 V DC connection for a system or chassis fan. • Fan is on in the S0 or S1 state. Fan is off when the system is off or in the S3, S4, or S5 state. • Wired to a fan tachometer input of the hardware monitoring and fan control ASIC. • Closed-loop fan control that can adjust the fan speed or switch the fans on or off as needed. • +12 V DC connection for a system or chassis fan. • Fan is on in the S0 or S1 state. Fan is off when the system is off or in the S3, S4, or S5 state. • Wired to a fan tachometer input of the hardware monitoring and fan control ASIC. • Closed-loop fan control that can adjust the fan speed or switch the fans on or off as needed. For information about The location of the fan connectors The location of the fan connectors and sensors for thermal monitoring The signal names of the fan connectors Refer to Figure 11, page 53 Figure 8, on page 34 Section 2.8.2.2, page 53 1.12.2.3 LAN Wake Capabilities CAUTION For LAN wake capabilities, the +5 V standby line for the power supply must be capable of providing adequate +5 V standby current. Failure to provide adequate standby current when implementing LAN wake capabilities can damage the power supply. LAN wake capabilities enable remote wake-up of the computer through a network. The LAN subsystem PCI bus network adapter monitors network traffic at the Media Independent Interface. Upon detecting a Magic Packet* frame, the LAN subsystem asserts a wake-up signal that powers up the computer. Depending on the LAN implementation, the Desktop Board D848PMB supports LAN wake capabilities with ACPI in the following ways: • The PCI bus PME# signal for PCI 2.2 compliant LAN designs • The onboard LAN subsystem 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
Product Description
39
1.12.2.2
Fan Connectors
Table 11 summarizes the function/operation of the fan connectors.
Table 11.
Fan Connector Function/Operation
Connector
Description
Processor fan
•
+12 V DC connection for a processor fan or active fan heatsink.
•
Fan is on in the S0 or S1 state.
Fan is off when the system is off or in the S3, S4, or S5 state.
•
Wired to a fan tachometer input of the hardware monitoring and fan control ASIC.
•
Closed-loop fan control (optional) that can adjust the fan speed or switch the fans
on or off as needed.
Front chassis fan
•
+12 V DC connection for a system or chassis fan.
•
Fan is on in the S0 or S1 state.
Fan is off when the system is off or in the S3, S4, or S5 state.
•
Wired to a fan tachometer input of the hardware monitoring and fan control ASIC.
•
Closed-loop fan control that can adjust the fan speed or switch the fans on or off
as needed.
Rear chassis fan
•
+12 V DC connection for a system or chassis fan.
•
Fan is on in the S0 or S1 state.
Fan is off when the system is off or in the S3, S4, or S5 state.
•
Wired to a fan tachometer input of the hardware monitoring and fan control ASIC.
•
Closed-loop fan control that can adjust the fan speed or switch the fans on or off
as needed.
For information about
Refer to
The location of the fan connectors
Figure 11, page 53
The location of the fan connectors and sensors for thermal monitoring
Figure 8, on page 34
The signal names of the fan connectors
Section 2.8.2.2, page 53
1.12.2.3
LAN Wake Capabilities
CAUTION
For LAN wake capabilities, the +5 V standby line for the power supply must be capable of
providing adequate +5 V standby current.
Failure to provide adequate standby current when
implementing LAN wake capabilities can damage the power supply.
LAN wake capabilities enable remote wake-up of the computer through a network.
The LAN
subsystem PCI bus network adapter monitors network traffic at the Media Independent Interface.
Upon detecting a Magic Packet* frame, the LAN subsystem asserts a wake-up signal that powers
up the computer.
Depending on the LAN implementation, the Desktop Board D848PMB supports
LAN wake capabilities with ACPI in the following ways:
•
The PCI bus PME# signal for PCI 2.2 compliant LAN designs
•
The onboard LAN subsystem