Intermec PB31 PB21 and PB31 Mobile Receipt Printer User Guide - Page 53

Send these commands to set a common name for server 1 and, is the passphrase.

Get Intermec PB31 PDF manuals and user guides View all Intermec PB31 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Chapter 2 - Configuring the PB21 and PB31 4 Send these commands to configure the EAP_TYPE: setup "8021x","EAP_TYPE","xxxx" where xxxx can be OFF, LEAP, PEAP, or TTLS. setup "8021x",".EAP_USER","xxxx" setup "8021x","EAP_PASS","xxxx" where xxxx is the unique username and the unique password for this protocol. 5 If you are using TTLS, you may need to send this command to set the TTLS outer name: setup "8021x","TTLS_USER","xxxx" where xxxx is the outer name. 6 If you are using certificates for validation, here are some commands you may need to use: • Send these commands to set a certificate and enable validation: setup "8021x","CA_CERT","c:/test.pfx@export" setup "8021x","VALIDATE","ON" where c:/test.pfx is the location and name of the certificate and export is the passphrase. • Send these commands to set a common name for server 1 and server 2: setup "8021x",".SERVER_CN1","xxxxxxxxxx" setup "8021x",".SERVER_CN2","xxxxxxxxxx" where xxxxxxxxxx can be a value from 0 to 64 characters. • Send this command to make sure your values match those used by the access point: setup write "8021x","uart1:" • You may need to send this command several times for the wireless station to connect: setup "wlan","ACTIVE","1" PB21 and PB31 Mobile Receipt Printer User Guide 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Chapter 2 — Configuring the PB21 and PB31
PB21 and PB31 Mobile Receipt Printer User Guide
41
4
Send these commands to configure the EAP_TYPE:
setup "8021x","EAP_TYPE","
xxxx
"
where
xxxx
can be OFF, LEAP, PEAP, or TTLS.
setup "8021x",".EAP_USER","
xxxx
"
setup "8021x","EAP_PASS","
xxxx
"
where
xxxx
is the unique username and the unique password for
this protocol.
5
If you are using TTLS, you may need to send this command to set
the TTLS outer name:
setup "8021x","TTLS_USER","
xxxx
"
where
xxxx
is the outer name.
6
If you are using certificates for validation, here are some
commands you may need to use:
•
Send these commands to set a certificate and enable validation:
setup "8021x","CA_CERT","
c:/test.pfx
@
export
"
setup "8021x","VALIDATE","ON"
where
c:/test.pfx
is the location and name of the certificate and
export
is the passphrase.
•
Send these commands to set a common name for server 1 and
server 2:
setup "8021x",".SERVER_CN1","
xxxxxxxxxx"
setup "8021x",".SERVER_CN2","
xxxxxxxxxx"
where
xxxxxxxxxx
can be a value from 0 to 64 characters.
•
Send this command to make sure your values match those
used by the access point:
setup write "8021x","uart1:"
•
You may need to send this command several times for the
wireless station to connect:
setup "wlan","ACTIVE","1"