Kenwood DDX574BH Instruction manual - Page 78

Installing the unit

Get Kenwood DDX574BH PDF manuals and user guides View all Kenwood DDX574BH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

CONNECTION/INSTALLATION ❏ Installation procedure 1 To prevent a short circuit, remove the key from the ignition and disconnect the · battery. 2 Make the proper input and output wire Installing the unit ❏ Installing the unit (only for DDX794/ DDX774BH/DDX594/DDX574BH/ DDX394) ❏ Installing the trim plate Attach the trim plate (2). 2 connections for each unit. 3 Connect the speaker wires of the wiring harness. 4 Connect the wiring harness wires in the following order: ground, battery, ignition. 5 Connect the wiring harness connector to the unit. 6 Install the unit in your car. • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). 7 Reconnect the · battery. 8 Press the reset button. (Page 3) 9 Configure . (Page 4) • Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. ❏ Installing the unit using the mounting bracket removed from the car 5 or 6 Car Bracket 5 or 6 • Select the appropriate type of screw for the mounting bracket: flat head (5) or round head (6). 78

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
78
CONNECTION/INSTALLATION
CONNECTION/INSTALLATION
❏
Installation procedure
1
To prevent a short circuit, remove the key
from the ignition and disconnect the
·
battery.
2
Make the proper input and output wire
connections for each unit.
3
Connect the speaker wires of the wiring
harness.
4
Connect the wiring harness wires in the
following order: ground, battery, ignition.
5
Connect the wiring harness connector to
the unit.
6
Install the unit in your car.
•
Make sure that the unit is installed securely
in place. If the unit is unstable, it may
malfunction (eg, the sound may skip).
7
Reconnect the
·
battery.
8
Press the reset button. (Page 3)
9
Configure
<Initial Setup>
. (Page 4)
Installing the unit
❏
Installing the unit (only for DDX794/
DDX774BH/DDX594/DDX574BH/
DDX394)
•
Bend the tabs of the mounting sleeve with a
screwdriver or similar utensil and attach it in place.
❏
Installing the unit using the mounting
bracket removed from the car
Car Bracket
5
or
6
5
or
6
•
Select the appropriate type of screw for the
mounting bracket: flat head (
5
) or round head
(
6
).
❏
Installing the trim plate
Attach the trim plate (
2
).
2