Konica Minolta KIP 75 Series KIP 75 Series Hardware User Manual - Page 2

(1)

Thank you for purchasing the Multi-Function Printer KIP 7570 Series.

This Hardware Operation Guide contains functional and operational explanations for the KIP 7570

Series.

Please read this Hardware Operation Guide carefully before using the printer.

Please keep this Hardware Operation Guide for future reference.

1.

When this product is installed in North America.

This product complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This product may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

FCC CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the product.

Note: This product has been tested and found to comply with the limits for a Class A digital

equipment, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the product is operated in a

commercial environment. This product generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual,, may cause

harmful interference to radio communications. Operation of this product in a residential area is

likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

This product complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions: (1) this product may not cause

interference, and (2) this product must accept any interference, including interference that may

cause undesired operation of this product.

Le présent appareil est conforme aux la partie 15 des règles de la FCC et CNR d’Industrie

Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux

deux conditions suivantes : (1) I’appareil ne doit pas produire de brouillage, et (2) I’utilisateur

de I’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d’en comprometter le fonctionnement.

Contains FCC ID: VP8-13551

Contains IC: 7391A-13551

2.

When this product is installed in Europe

This product complies with the requirements in CISPR 32 for a Class A computing equipment.

Operation of this product in a residential area may cause unacceptable interference to radio

and TV reception requiring the operator to take whatever steps are necessary to correct the

interference.

Do not install product around other electronic equipment or other precision instruments.

Other equipment may be effected by electrical noise during operation.

If the product is installed near other electronic equipment, such as a TV or a radio,

interference to said equipment, such as noise or flickering, may occur.

Use a separate power line and install the PRINTER as far as possible from said equipment.

Section	Page
KIP 7570 Series Hardware User Manual A.0	1
Safety	4
WARNING	5
CAUTION	6
POWER CORD INSTRUCTION	7
Chapter 1 Before Use	8
1. 1 Installation Requirements	9
1. 2 Originals Prohibited from Duplication	10
1. 3 Features	11
1. 4 Specifications	12
1. 4. 1 General	12
1. 4. 2 Printer part	13
1. 4. 3 Scanner part (for MFP Model)	15
1. 5 Appearance	16
1. 5. 1 Front view	16
1. 5. 2 Rear view	17
1. 6 Specifications for Scan Original (for MFP Model)	18
1. 6. 1 Original Standards	18
1. 6. 2 Special Documents	18
1. 6. 3 “Do Not Scan” Originals	19
1. 7 Specifications for the Printing Media	22
1. 7. 1 Papers not available to use	22
1. 7. 2 Keeping the paper in the custody	23
1. 7. 3 Treatment against environmental condition	24
Chapter 2 Basic Operation	25
2. 1 Turning on the Printer	26
2. 2 Turning off the Printer	28
2. 3 Replacing Roll Media	29
2. 4 Replacing Toner Cartridge	35
2. 5 Cut Sheet Media	40
2. 6 Copying (for MFP Model)	41
2. 7 Stop of Scan or Copy (for MFP Model)	44
2. 8 Dehumidifying Roll Media	45
Chapter 3 Error Correction	46
3. 1 Paper Jam	47
3. 1. 1 Roll Deck Section Jam (Deck 1, 2 Mis-feed)	48
3. 1. 2 Manual Feeder Section Jam(Registration Mis-feed)	51
3. 1. 3 Media Feed Section Jam(Registration Mis-feed, Separation Mis-feed)	53
3. 1. 4 Fuser Section Jam (Exit Back Mis-feed)	55
3. 1. 5 Stack Jam	59
3. 1. 6 Original Jam (for MFP Model)	61
3. 1. 7 Accessory Jam	62
3. 2 Door Open	63
3. 2. 1 Roll Deck (Deck 1 Open, Deck 2 Open)	63
3. 2. 2 Engine Unit (Front Cover Open)	63
3. 2. 3 Paper Exit Door (Paper Exit Door Open)	64
3. 2. 4 Scanner Unit (Scanner feeder open) (for MFP Model)	64
3. 3 Other Operator Call Error	65
3. 3. 1 Roll Replacement	65
3. 3. 2 Toner Empty	65
3. 3. 3 Accessory Error	65
3. 4 Service Call Errors	66
Chapter 4 Maintenance	67
4. 1 Scanner Unit (for MFP Model)	68
4. 1. 1 Scan Glass, Feed Roller, Guide Plate	68
4. 1. 2 Sensor	71

Konica Minolta KIP 75 Series KIP 75 Series Hardware User Manual - Page 2

This product complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS

Page 2 highlights