Konica Minolta KIP 75 Series KIP 75 Series Hardware User Manual - Page 45

Dehumidifying Roll Media, HL

Get Konica Minolta KIP 75 Series PDF manuals and user guides View all Konica Minolta KIP 75 Series manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

2. 8 Dehumidifying Roll Media For avoiding dehumidifying of roll media in the Roll Deck, Printer has an optional part DEHUMIDIFY KIT. When creasing of media or void of image is seen caused by the humidifying of roll media, it is recommended to use this kit. Ask your service personnel for DEHUMIDIFY KIT. If the roll paper is extremely humidified, it may cause several kinds of defective print. Defective prints you will experience most will be "crease of paper" and "loss of image". Normal Print Crease of paper If the media is humidified; Normal Print Loss of image If the media is humidified; If the Printer is installed in such a condition, it is recommended to use the optional embedded "Dehumidify Heater". Turn on the Dehumidify Heater if the room air has too much humidity (75% or higher) to prevent the above kinds of print defect. Such problems above may be resolved. To turn on the Dehumidify Heater, press the H side of the Dehumidify Heater Switch on the rear. (Press its L side to turn off.) H L 2-21 Chapter 2 Basic Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Chapter 2
Basic Operation
2-21
2. 8
Dehumidifying Roll Media
If the roll paper is extremely humidified, it may cause several kinds of defective print.
Defective prints you will experience most will be “crease of paper” and “loss of image”.
If the Printer is installed in such a condition, it is recommended to use the optional embedded
“Dehumidify Heater”.
Turn on the Dehumidify Heater if the room air has too much humidity (75% or higher) to prevent
the above kinds of print defect.
Such problems above may be resolved.
To turn on the Dehumidify Heater, press the H side of the Dehumidify Heater Switch on the rear.
(Press its L side to turn off.)
H
L
Normal Print
Normal Print
If the media is humidified;
If the media is humidified;
Crease of paper
Loss of image
For avoiding dehumidifying of roll media in the Roll Deck, Printer has an optional part
DEHUMIDIFY KIT. When creasing of media or void of image is seen caused by the
humidifying of roll media, it is recommended to use this kit. Ask your service
personnel for DEHUMIDIFY KIT.