Konica Minolta KIP 75 Series KIP 75 Series Hardware User Manual - Page 23

Keeping the paper in the custody, Replacing Roll Media].

Get Konica Minolta KIP 75 Series PDF manuals and user guides View all Konica Minolta KIP 75 Series manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Pre-printed Extremely slippery Extremely sticky Extremely thin and soft OHP Film CAUTION Do not use the paper with staple, or do not use such conductive paper as aluminium foil and carbon paper. The above may result in a danger of fire. NOTE (1) Print image may become light if printed on a rough surface of the paper. (2) Print image may become defective if the print paper has an excess curl. (3) It will become a cause for paper mis-feed, defective print image or paper creasing if you use a paper that does not satisfy the specification. (4) Do not use a paper of which surface is very special, such as thermal paper, art paper, aluminium foil, carbon paper and conductive paper. (5) Do not use papers with unpacked (exposed in high / low temperature & humidity) in a long period. Such papers may result in mis-feed, defective image or paper creasing. (6) Tracing paper exposed to air over a long period tends to cause a defective printing. Removing one round on the surface of the tracing roll paper from the beginning is recommended. Refer to [2.3 Replacing Roll Media]. 1. 7. 2 Keeping the paper in the custody Keep the paper in the custody taking care of the following matters. 1. Do not expose the paper to the direct sunlight. 2. Keep the paper away from high humidity. (It must be less than 70%) 3. Put the paper on a flat place 4. If you will keep the paper in the custody, which you have already unpacked, put it into the polyethylene bag to avoid the humidity. 1-16 Chapter 1 Before Use

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Chapter 1
Before Use
1-16
Pre-printed
Extremely slippery
Extremely sticky
Extremely thin and soft
OHP Film
1. 7. 2
Keeping the paper in the custody
Keep the paper in the custody taking care of the following matters.
1.
Do not expose the paper to the direct sunlight.
2.
Keep the paper away from high humidity. (It must be less than 70%)
3.
Put the paper on a flat place
4.
If you will keep the paper in the custody, which you have already unpacked, put it into the
polyethylene bag to avoid the humidity.
CAUTION
Do not use the paper with staple, or do not use such conductive paper as aluminium foil and
carbon paper.
The above may result in a danger of fire.
NOTE
(1)
Print image may become light if printed on a rough surface of the paper.
(2)
Print image may become defective if the print paper has an excess curl.
(3)
It will become a cause for paper mis-feed, defective print image or paper creasing if you
use a paper that does not satisfy the specification.
(4)
Do not use a paper of which surface is very special, such as thermal paper, art paper,
aluminium foil, carbon paper and conductive paper.
(5)
Do not use papers with unpacked (exposed in high / low temperature & humidity) in a
long period. Such papers may result in mis-feed, defective image or paper creasing.
(6)
Tracing paper exposed to air over a long period tends to cause a defective printing.
Removing one round on the surface of the tracing roll paper from the beginning is
recommended.
Refer to [2.3
Replacing Roll Media].