Konica Minolta Kodak i5850 User Guide - Page 56

Installing/Replacing the ink blotter strips (Front printer only), Consumables

Get Konica Minolta Kodak i5850 PDF manuals and user guides View all Konica Minolta Kodak i5850 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

6. Slide the printer carrier into the desired print position. See the section entitled "Changing print positions" earlier in this chapter. 7. Close the front printer access cover and reinstall the output tray or reinstall the rear access printer door. 8. Run a print test (see the section entitled, "Performing a print test" in Chapter 3). Installing/Replacing the ink blotter strips (Front printer only) The three ink blotter strips on the scanner transport collect ink overflow from the printer. These strips should have been installed in the ink blotter channels at the time of printer installation. If they have not been installed, the following steps can be performed to install these strips for the first time. Replace these strips as ink overflow collects on the blotter(s). Depending on your print position, all strips may not need to be replaced at the same time. To order additional ink blotter strips, see the section entitled, "Supplies and Consumables" in Chapter 7. NOTE: No ink blotters are required for the rear printer. 1. Pull the scanner cover release latch forward to release and lift the scanner cover. 2. Remove the black drainage strip from the transport. 3. Locate the blotter strip channel. These channels are where the blotter strips will be installed or replaced. 4. If you are replacing a blotter strip, proceed with Step 5. If you are installing the blotter strips for the first time, go to Step 6. A-61670 August 2014 4-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
A-61670
August 2014
4-7
6.
Slide the printer carrier into the desired print position. See the section
entitled “Changing print positions” earlier in this chapter.
7.
Close the front printer access cover and reinstall the output tray or reinstall
the rear access printer door.
8.
Run a print test (see the section entitled, “Performing a print test” in
Chapter 3).
Installing/Replacing
the ink blotter strips
(Front printer only)
The three ink blotter strips on the scanner transport collect ink overflow from
the printer. These strips should have been installed in the ink blotter channels
at the time of printer installation. If they have not been installed, the following
steps can be performed to install these strips for the first time.
Replace these strips as ink overflow collects on the blotter(s). Depending on
your print position, all strips may not need to be replaced at the same time. To
order additional ink blotter strips, see the section entitled, “Supplies and
Consumables” in Chapter 7.
NOTE:
No ink blotters are required for the rear printer.
1.
Pull the scanner cover release latch forward to release and lift the scanner
cover.
2.
Remove the black drainage strip from the transport.
3.
Locate the blotter strip channel. These channels are where the blotter
strips will be installed or replaced.
4.
If you are replacing a blotter strip, proceed with Step 5. If you are installing
the blotter strips for the first time, go to Step 6.