Kyocera KM-C2230 Fiery X3e 22C-KM User Software Install Guide for KM-C2230 - Page 49

Setting up SMB printing on Windows NT 4.0, Microsoft Networks.

Get Kyocera KM-C2230 PDF manuals and user guides View all Kyocera KM-C2230 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

11-33 Setting up PostScript or PCL printing with Windows NT 4.0 Setting up SMB printing on Windows NT 4.0 SMB printing (also known as Windows printing) allows you to install the PostScript or PCL printer driver and printer description files, and print from your computer to a particular print connection (Hold, Print, or Direct) on the Fiery X3e. These instructions assume you have installed the TCP/IP protocol and Client for Microsoft Networks. Each connection (Hold, Print, or Direct) requires a new printer driver and printer description file. To set up printing to a second or third print connection, repeat the procedure "To set up SMB printing on Windows NT 4.0" on page 1-34. If you install more than one printer, give each a descriptive name during printer driver installation, such as Aero-Print or Aero-Hold, so you can easily identify printers. NOTE: To change printer defaults and configure installable options from Windows NT 4.0, you must log on with the special log-in name, 'efi_admin_efi' (instead of Administrator) and use the password specified in Fiery X3e Setup. If you log on as a User, you can install the printer driver through Point and Print, but you cannot modify printer defaults and configure installable options. BEFORE YOU BEGIN • Configure the Fiery X3e for SMB printing in Run Setup>Network Setup>Service Setup> Windows Setup. SMB printing is referred to as Windows Printing in Setup, on the Control Panel Map, and on the Configuration page. For more information, see the Configuration Guide.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
1
1-33
Setting up PostScript or PCL printing with Windows NT 4.0
Setting up SMB printing on Windows NT 4.0
SMB printing (also known as Windows printing) allows you to install the PostScript or
PCL printer driver and printer description files, and print from your computer to a
particular print connection (Hold, Print, or Direct) on the Fiery X3e. These
instructions assume you have installed the TCP/IP protocol and Client for
Microsoft Networks.
Each connection (Hold, Print, or Direct) requires a new printer driver and printer
description file. To set up printing to a second or third print connection, repeat the
procedure
“To set up SMB printing on Windows NT 4.0”
on page 1-34. If you install
more than one printer, give each a descriptive name during printer driver installation,
such as
Aero-Print
or
Aero-Hold
, so you can easily identify printers.
N
OTE
:
To change printer defaults and configure installable options from Windows
NT 4.0, you must log on with the special log-in name, ‘efi_admin_efi’ (instead of
Administrator) and use the password specified in Fiery X3e Setup. If you log on as a
User, you can install the printer driver through Point and Print, but you cannot modify
printer defaults and configure installable options.
B
EFORE
YOU
BEGIN
•
Configure the Fiery X3e for SMB printing in Run Setup>Network Setup>Service
Setup>Windows Setup.
SMB printing is referred to as Windows Printing in Setup, on the Control Panel Map,
and on the Configuration page. For more information, see the
Configuration Guide
.