LG LP070HED1 Service Manual - Page 36

Leveling Leg Assembly, Installation on Wall Sleeve, Leveling Leg Assembly,

Get LG LP070HED1 PDF manuals and user guides View all LG LP070HED1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Leveling Leg Assembly To install the leveling leg assembly, complete the following: 1. Drill two 1/8-inch holes in each side of the wall sleeve, as shown in Figure 45, using the leveling leg assembly as a template. Locations near the front of the sleeve provide more support. 2. Adjust the leveling legs to the approximate height needed and install them on either side of the wall sleeve, using the screws provided. Bottom of wall sleeve can be anywhere from three to five inches above the screw base. Caulk around screws to prevent water leaks. 3. Level the sleeve horizontally from side-to-side. Provide a slight slope (one-quarter bubble in the sight glass) toward the outside. Check the level again after the unit has been installed. Adjust the legs as needed. Figure 45 - Leveling Leg Assembly Leveler Bracket Speed Grip Nut Adjuster Screw 1/2" 1" 1/4" Installation on Wall Sleeve 1. Drill four 1/8-inch diameter holes in the wall sleeve, two on each side, using the leveling legs as a template. Caulk around screws to prevent water leaks. 2. Attach the legs to the wall sleeve, using the screws provided. 3. Adjust the leveling legs to level the wall sleeve from side to side and provide a slight pitch to the outside (one-quarter bubble in sight glass). Figure 46 - Leveling Leg Installation on Wall Sleeve 1/8" Diameter holes (four required per unit field-drilled) NOTES: 1. Two leveling legs are supplied in each kit. 2. One kit is required per unit. 3. Fout mounting screws are provided in each kit. Downloaded from www.Manualslib.com manuals search engine -36-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
—36—
Leveling Leg Assembly
To install the leveling leg assembly, complete the following:
1. Drill two 1/8-inch holes in each side of the wall sleeve, as
shown in Figure 45, using the leveling leg assembly as a
template. Locations near the front of the sleeve provide
more support.
2. Adjust the leveling legs to the approximate height needed
and install them on either side of the wall sleeve, using the
screws provided. Bottom of wall sleeve can be anywhere
from three to five inches above the screw base. Caulk
around screws to prevent water leaks.
3. Level the sleeve horizontally from side-to-side. Provide a
slight slope (one-quarter bubble in the sight glass) toward
the outside. Check the level again after the unit has been
installed. Adjust the legs as needed.
Installation on Wall Sleeve
1. Drill four 1/8-inch diameter holes in the wall sleeve, two on
each side, using the leveling legs as a template. Caulk
around screws to prevent water leaks.
2. Attach the legs to the wall sleeve, using the screws
provided.
3. Adjust the leveling legs to level the wall sleeve from side to
side and provide a slight pitch to the outside (one-quarter
bubble in sight glass).
Adjuster Screw
Speed Grip Nut
Leveler Bracket
1/8" Diameter holes
(four required per unit field-drilled)
1"
1/4"
1/2"
NOTES:
1. Two leveling legs are supplied in each kit.
2. One kit is required per unit.
3. Fout mounting screws are provided in each kit.
Figure 45 - Leveling Leg Assembly
Figure 46 - Leveling Leg Installation on Wall Sleeve
Downloaded from
www.Manualslib.com
manuals search engine