Lantronix EDS3000PS Command Reference - Page 14

EDS3000 Command Reference

Get Lantronix EDS3000PS PDF manuals and user guides View all Lantronix EDS3000PS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

3: Command Line Interface Commands at the login level (see Figure 3-2 Login Level Commands below) do not affect current configuration settings and are not displayed initially. If you type?, you will see the login subcommands. These commands provide diagnostic and status information only. Figure 3-2 Login Level Commands admin@EDS3032PR-0080a38aa011>? clrscrn iperf ping show show lines show routes tcpdump trace route exit ping ping show history show multicast routes show rules trace route enable admin@EDS3032PR-0080a38aa011> Note: To configure the EDS3000 device server, you must be in the enable level and any of its sub-levels. Figure 3-3 Enable Level Commands below shows the enable level commands. Figure 3-3 Enable Level Commands admin@EDS3032PR-0080a38aa011(enable)# admin@EDS3032PR-0080a38aa011(enable)#? auto show interfaces clrscrn connect device dns exit iperf kill telnet ping ping reload factory defaults show history show ip sockets show multicast routes show routes show sessions ssh ssl telnet trace route tunnel xml auto show processes configure connect line disable email filesystem kill ssh line ping reload show show interfaces show lines show processes show rules ssh ssh tcpdump telnet trace route write admin@EDS3032PR-0080a38aa011(enable)# admin@EDS3032PR-0080a38aa011(enable)# Refer to the 6: Commands and Levels at the end of this document for a complete list of levels, commands, and descriptions. EDS3000 Command Reference 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
3: Command Line Interface
EDS3000 Command Reference
14
Commands at the login level (see
Figure 3-2 Login Level Commands
below) do not affect current
configuration settings and are not displayed initially. If you type
?
, you will see the login
subcommands. These commands provide diagnostic and status information only.
Figure 3-2 Login Level Commands
admin@EDS3032PR-0080a38aa011>?
clrscrn
exit
iperf <params>
ping <host>
ping <host> <count>
ping <host> <count> <timeout>
show
show history
show lines
show multicast routes
show routes
show rules
tcpdump <parameters>
trace route <host>
trace route <host> <protocol>
enable
admin@EDS3032PR-0080a38aa011>
Note:
To configure the EDS3000 device server, you must be in the enable level and any
of its sub-levels.
Figure 3-3 Enable Level Commands
below shows the enable level
commands.
Figure 3-3 Enable Level Commands
admin@EDS3032PR-0080a38aa011(enable)#
admin@EDS3032PR-0080a38aa011(enable)#?
auto show interfaces
auto show processes
clrscrn
configure
connect
connect line <line>
device
disable
dns
email <number>
exit
filesystem
iperf <params>
kill ssh <session>
kill telnet <session>
line <line>
ping <host>
ping <host> <count>
ping <host> <count> <timeout>
reload
reload factory defaults
show
show history
show interfaces
show ip sockets
show lines
show multicast routes
show processes
show routes
show rules
show sessions
ssh
ssh <optClientUsername> <host>
ssh <optClientUsername> <host> <port>
ssl
tcpdump <parameters>
telnet <host>
telnet <host> <port>
trace route <host>
trace route <host> <protocol>
tunnel <line>
write
xml
admin@EDS3032PR-0080a38aa011(enable)#
admin@EDS3032PR-0080a38aa011(enable)#
Refer to the
6: Commands and Levels
at the end of this document for a complete list of levels,
commands, and descriptions.